Reddit reviews Uriveusa 12V Car Add-A-Circuit Fuse TAP Adapter Fuse Holder with 10A, 20A Fuse [Upgraded Fuses] - (2 Pack) (Micro2 Fuse)
We found 5 Reddit comments about Uriveusa 12V Car Add-A-Circuit Fuse TAP Adapter Fuse Holder with 10A, 20A Fuse [Upgraded Fuses] - (2 Pack) (Micro2 Fuse). Here are the top ones, ranked by their Reddit score.
Plug Into An Existing Fuse Holder / HIGH QUALITY PRODUCTProtects Original Circuit and Provides A Lead For New Circuit16-gauge red wire lead for new circuit is 5 inches long / includes insulated crimp-type coupler butt connector.Includes Add-a-circuit Fuse TAP(2pcs) / 10A (2pcs), 20A (2pcs) Amp fuses[UPGRADED HIGH QUALITY FUSES] 10A (2pcs), 20A (2pcs) Amp Fuses!!
I understand not everyone is mechanically inclined, but I hate to see people paying for a dashcam install. They're one of the simplest installs you can do on a car! Even if you've never wired anything in your life, it's pretty simple! If you really hate the cigarette adapter and want to hide your wires, all you need is about $8 on amazon, or at autozone, oreillys, anywhere for an "adapt a fuse".
You just need to connect the positive from the dashcam to this baby and pop it in the fuse panel (almost always located in the car). Connect the negative to just about anything metal in the car and it's grounded.
Like others have said, be sure you bought a dashcam with a capacitor and not a battery. The heat out here will ruin the battery, fast. The capacitors have a little easier of a time.
Good luck!
https://www.amazon.com/Uriveusa-Circuit-Adapter-Holder-Upgraded/dp/B01LFXA5YQ/ref=sr_1_1_sspa?keywords=car+fuse+adapter&qid=1564186478&s=gateway&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzQzgxMlkwMU9DNjhKJmVuY3J5cHRlZElkPUEwNzA1NDIxQk9FVTQ1TkszUkI0JmVuY3J5cHRlZEFkSWQ9QTAwMjMyMjgzOEQ1RjdSNTdRSVhKJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==
Most people will find a switched wire at the fuse panel using a fuse tap.
If you get one, also get the TAP adapter, and the Hardwire kit. They're pretty cheap.
Using this, I ran the hardwire kit up behind the rear view mirror, behind the headliner, down the plastic on the A pillar, and back behind the kickpanel and into the fuse box with the TAP adapter. I can't remember which fuse I used without looking but it's wired into one where the camera automatically comes on whenever the accessory is active or the truck is running. When I turn off the truck, the camera turns off, automatically. I don't have to do anything except clear off the saved videos once every 6 months or so.
Terminals: (need 2, get at least 10, you'll mangle at least a couple) https://www.digikey.com/product-detail/en/molex/0330122001/WM2989CT-ND/2405588
Add-a-circuit: https://www.amazon.com/Uriveusa-Circuit-Adapter-Holder-Upgraded/dp/B01LFXA5YQ
Also need some 16g wire (or so, 16 is the smallest that properly fits the blue crimp connection on the add-a-fuse, though I'd recommend using heat-shrinkable butt splices instead, just for the water proofing).
Thank you!
Is this the correct hardware kit?
https://www.amazon.com/Viofo-3-Wire-Hardwire-A129-Camera/dp/B07KZGM9LS/ref=sr_1_2?crid=QK7O5MVGQXYV&keywords=viofo+3+wire+acc+hardwire+kit&qid=1569346851&sprefix=Viofo+3-wire+hardwire+kit%2Caps%2C227&sr=8-2
Is this the correct tap-a-fuse kit?
https://www.amazon.com/Uriveusa-Circuit-Adapter-Holder-Upgraded/dp/B01LFXA5YQ/ref=sr_1_1?keywords=tap-a-fuse+wire&qid=1569346818&sr=8-1