Reddit reviews Freud 10" x 24T Thin Kerf Rip Blade (LU87R010)

I've only done them for 2 or 3 pieces so far, but you can do a good shaker with cope and stick style. This video from saw stop does a decent job of summarizing things, but do additional googleing to get all the details.

https://youtu.be/d-fCL-ZAVWs

Also, get a ftg rip blade for cutting the groove, any bevel will make it impossible to get a good tight fit. Here is the one I use with good success (then you have a real rip blade too!) I'd totally recommend the thin kerf if you have a 1.5hp or less saw.

https://www.amazon.com/gp/aw/d/B0000225UH/ref=mp_s_a_1_1?ie=UTF8&qid=1468094452&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=Freud+thin+kerf+ftg+rip

A general purpose blade (even the fancy Forrest) won't solve your problem--it still has too many teeth for ripping thick hardwoods efficiently on a <3HP saw. I lost count of how many times I stopped the blade when ripping moderate-hardness woods like Walnut and Soft Maple on my last table saw, which was comparable to yours.

The glue-line-rip is a one trick pony. You're looking for a general use rip blade.

I would recommend the 24T Freud Industrial Thin Kerf Rip (not diablo).

BTW, the "3HP" on your saw is marketing nonsense--you can't get more than about 1.75HP out of a 120V/15A circuit.

I've liked the rip cuts I get from my Freud thin kerf rip blades.

http://www.amazon.com/Freud-LM75R010-10-Inch-8-Inch-Arbor/dp/B001V5J4QY/ref=sr_1_2?s=hi&ie=UTF8&qid=1421010296&sr=1-2&keywords=freud+thin+rip+blade

http://www.amazon.com/Freud-LU87R010-10-Inch-24-Tooth-PermaShield/dp/B0000225UH/ref=sr_1_1?s=hi&ie=UTF8&qid=1421010296&sr=1-1&keywords=freud+thin+rip+blade

The thin blade eats less wood and for underpowered saws like mine works well.
I prefer the FTG blade because it's a little more aggressive and doesn't leave the tiny triangle of wood in the corners if you use it for a non through cut. Not an issue for re saws though.

Any contractor saw would be excellent. You should look for saws with the motor hanging out the back, they're better than the direct drives. Everyone here loves the delta -I cant remember the number- or the Rigid, but I've got a mid 90s craftsman with new freud blades and it cuts very smoothly. I tuned it up following youtube's guides and then every time i adjust the fence have to square it up for 2 minutes cause I havent had time to build a biesemeyer fence yet. I got these two saw blades 24 tooth FTB and 60 tooth ATB

Build yourself a crosscut sled for 10$ worth of wood and I used it for rabbets and Miter-ing. This table saw is a pretty decent deal. Bet he'd take 300 for it

Dont be afraid of used things, youtube will tell you how to make it pretty decent.

The contractor comes with their rather shitty 40t, full kerf combo blade. Its not a great blade, and its full kerf. Lots of full kerf blades will perform better, let alone a thin kerf. Its also a relatively loud blade compared to many on the market.

If you haven't bought blades already and are still researching, I use a Freud 24t thin kerf rip blade and 50t combo blade and I've been very happy with them.

The rip blade can easily handle ripping 45mm redgum (12kN on the janka scale) without bogging down.

For the cost of a blade just to save an extra ~0.025 inches or whatever or wood you can just buy a LOT more board feet of lumber instead. Or resaw on a bandsaw.

I think the blade that dewalt comes with is technically close to thin kerf (3/32 ~= 0.095 I think I have the same blade that came with my Dewalt..24 tooth 0.095 kerf).

A normal kerf is 1/8 or 0.125, to go even thinner you are talking like 1/32 of an inch less per cut I don't think you'll find a 1/16 blade for a TS and if you do it will cost a lot.

A 56.00 Freud thin kerf blade is also basically the same as what's in your saw https://www.amazon.ca/Freud-LU87R010-10-Inch-Ripping-Perma-Shield/dp/B0000225UH/ref=sr_1_3?ie=UTF8&qid=1526935425&sr=8-3&keywords=freud+thin+kerf

So just save your money on a new blade and buy more lumber

I had some issues with my 4512 also bogging down. I bought a Freud 24 tooth thin rip blade and it works great. I haven't had any problems since. The thinner the kerf the easier it is for the saw to cut.

http://www.amazon.com/Freud-LU87R010-10-Inch-24-Tooth-PermaShield/dp/B0000225UH

I have the same saw and I bought this for it -- https://www.amazon.com/Freud-Tooth-Ripping-Blade-LU87R010/dp/B0000225UH/ref=sr_1_1?ie=UTF8&qid=1506016279&sr=8-1&keywords=thin+kerf+saw+blades+10-inch

I like the thin kerf as you don't have to worry about it bogging down if you cut anything thick, and I do mostly rip cuts. I've ripped and cross cut plywood with a thin maple veneer and haven't had any issues with tear out either.

Never mind my suggestion, it'll probably ruin your veneer.

Depending on the finish needed, you might want to switch to using a blade with less teeth - something made more for ripping.
A smaller blade, with just as many teeth won't be any cheaper to resharpen.
I just got the following blade (Freud LU87R010 10-Inch 24-Tooth - http://www.amazon.com/Freud-LU87R010-10-Inch-24-Tooth-PermaShield/dp/B0000225UH/ref=sr_1_1?s=hi&ie=UTF8&qid=1381425527&sr=1-1&keywords=freud+lu87), so I can't commend on its longevity, but it seems more suited to your needs.
Should be at least half as expensive to resharpen.

If you do attempt this on your machine, you will want a thin-kerf rip blade, 20-30 teeth. The thin kerf will reduce the load on your machine.

Heres a decent Freud one for under 40 bucks from Amazon.