Best motion-activated wall switches according to redditors
We found 122 Reddit comments discussing the best motion-activated wall switches. We ranked the 34 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 122 Reddit comments discussing the best motion-activated wall switches. We ranked the 34 resulting products by number of redditors who mentioned them. Here are the top 20.
Lutron Maestro Motion Sensor Switch, No Neutral Required, 250 Watts, Single-Pole, MS-OPS2-WH, White https://www.amazon.com/dp/B005WM3ALC/ref=cm_sw_r_cp_api_i_s-AVDbA71VAS2
Occupancy sensor (automatic light switch) in the basement, laundry, and walk-in closets. We got these Lutron models from Amazon for $20. Set them to 1 or 2 minutes for the closets, a little more for the laundry, and whatever works for you for the basement. Not having to reach for the light switch with your hands full is really convenient.
http://imgur.com/a/4ODHn
From https://www.amazon.com/Philips-464602-Hue-Motion-Sensor/dp/B01KJYSOGI/ref=sr_1_1?ie=UTF8&qid=1475186677&sr=8-1&keywords=hue+motion+sensor
I have an Ecobee4 thermostat (although Alexa doesn’t work as well for me as I hoped) w/ Ecobee remote sensors mounted in every room. Not only is this great for managing the temp in the house overall, but now I can include temp changes in my automations and geo-fencing.
In addition, although I find them a bit slow to respond when using them as room entry motion sensors, the Ecobee remote sensors are great for automatically turning off the lights when a room is no longer occupied.
I also recently added some non-HomeKit “smarter” switches in my bathroom and laundry room. In the laundry room, I put a simple Lutron (not Caseta) motion sensor switch to auto turn the light on/off when someone comes/goes from the laundry room. Works fantastically, it’s simple, and not too expensive.
In my bathroom, I added three new Lutron (not Caseta) switches.
The first two of those switches are far more programmable than I thought... reading the instructions really paid off! :)
The Lutron Claro wall plates are really great as well. They are very clean, simple, and modern looking... and their 2-part design makes it really easy to adjust all your switches for a precision installation (i.e. flush and straight).
In my bedroom, my bedside lamps are controlled by 1 Lutron Caseta lamp dimmer w/ remote. I use the same style Caseta lamp dimmer for a few other standalone lamps... and even used one to automate (just on/off) my outside LED holiday lights last winter (the dimmability of which was fantastic, as they are normally way too bright).
In conclusion, before spending a bunch of money, my advice would be to think carefully about how you/others use certain rooms and if a motion detection switch would suffice or if a more complex automation control is needed. Also... do the math. As others have pointed out, one alternative may be way more cost effective over another when you factor in the number of bulbs and/or switches involved.
One last thing... I am renting a room to a guy who's on a totally different schedule than me and as such, I never knew if he was in his room sleeping or out of the house elsewhere. So... since I had previously added him to my HomeKit household... I use a combination of geofencing with his phone, and the Ecobee motion sensor in his room, to switch on/off a particular lamp when he comes & goes. That way... it's easy for me to know if I need to be quiet, or if I can rock out with my socks out.
*EDIT: Added a bunch of links and more...
USB ports for friends who come over and want to charge their phones: http://www.amazon.com/gp/product/B00IAZIU5Y?psc=1&redirect=true&ref_=oh_aui_search_detailpage
Timer for the shower fan so you don't always leave it on: http://www.amazon.com/gp/product/B007BJULYS?psc=1&redirect=true&ref_=oh_aui_detailpage_o09_s00
Motion activated lights everywhere, esp the closets: http://www.amazon.com/gp/product/B005WM3ALC?psc=1&redirect=true&ref_=oh_aui_detailpage_o08_s00
Edit: formatting
replace your light switch with this
I have found non-smart but programmable items (like your roomba) tend to be much more affordable and much easier to install and use.
You can get sensors for lights (bathroom humidity, movement, etc) that are pretty cheap/easy to install (even timers aren't too bad).
Look into more programmable items than wifi/connected if you want to save money. A Nest is a great start, and you can connect lights/garage/etc to it, but it goes way beyond that. Set it and forget it are great!
Various links below for ideas, but not necessarily these products. I've bought some from Amazon/Lowes/etc and have had mixed success. I'd check product reviews.
For Hallways and stuff
Bathroom fan/light
Wifi/Remote Lighting
Locks for Front door
For Blinds/etc
-- I've not used this, but my friends have something similar and its pretty neat
Good luck, let me know if you do any of these, and have any success with them.
For that kind of money you could easily get a 4-way (or 5-way) bulb adaptor plus 4-5 100w LED bulbs which would be TWICE as bright.
$14.99 for the fixture:
https://www.amazon.com/gp/product/B01DVUDDC2/ref=crt_ewc_img_gw_2?ie=UTF8&psc=1&smid=A3UENWQOYWIPH9
$35 for 4 LED floodlights that are 100w each:
https://www.amazon.com/gp/product/B00RMK05Y2/ref=crt_ewc_img_gw_1?ie=UTF8&psc=1&smid=A1VCN0ZD746TM9
Pick up a motion sensing light switch for $21:
https://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=sr_1_1?ie=UTF8&qid=1485043085&sr=8-1&keywords=motion+sensing+light+switch
That will be 500 watts versus 228 watts for only $71, saving you $50 per fixture. Got two like I do? $142 instead of $260!
Now, if something goes wrong, you can replace the bulbs or fixture cheaply. Or take it with you.
Bonus? You don't even have to remove your existing ceiling socket. This all just screws right in!
I've got something like this. You can put it into a plate designed for a GFCI. Basically just replace your existing light switch.
http://www.amazon.com/TOPGREENER-TSOS5-W-Single-Pole-Fluorescent-Incandescent/dp/B015G8VLNA%3FSubscriptionId%3DAKIAILSHYYTFIVPWUY6Q%26tag%3Dduckduckgo-ffnt-20%26linkCode%3Dxm2%26camp%3D2025%26creative%3D165953%26creativeASIN%3DB015G8VLNA
I used a Lutron Maestro switch. The lights are direct wired to it (through the walls) in my case.
http://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=sr_1_1?ie=UTF8&qid=1465245428&sr=8-1&keywords=lutron+occupancy+sensor
It isn't a kit, but any light that can be powered from normal home AC power will work with it.
Hi, I know its not exactly what you are asking, but I just picked up two of the ge z-wave motion sensors for $12 (all the ge z-wave stuff was marked down) at walmart a few weeks ago. They are battery operated and work really well. I saw some complaints about battery life, but I've had them for a few weeks and its still showing 100%, I think just RTFM and set good rules and then they are good devices. I have one on my front porch which turns the house on reliably and one inside to activate dimmed lights inside at night. They work really well- my cats don't set them off, but humans always do.
Here is the model: https://www.amazon.com/GE-Wireless-Activation-Monitoring-34193/dp/B01KQDIU52/
What this guy said. I'll elaborate that it'll likely be difficult to find 277V dimmers or switches. In my opinion, you're looking for motion activated lighting (most proven and prevalent) or a scheduler instead of automation. Like this.
http://www.amazon.com/Leviton-ODS10-ID-Decora-277-Volt-Occupancy/dp/B0007N72P6
I'd also recommend that "home automation" is a different bird than office/industrial settings. What I mean by that is with "automation" you can have logic. IF the motion in the kitchen trips, AND the shades are up, AND it's between sunrise and sunsert, THEN turn on the lights.
Industrial building management and automation is a complete industry. What would your system do if the power fails or browns while there's a fire and people aren't out? Is your system which potentially manages a building with high density be NFPA certified? Up to local code? Etc.
Up here on Amazon US for release on Oct. 2.
I think it is this model (on Amazon):
https://www.amazon.com/GE-Wireless-Activation-Monitoring-34193/dp/B01KQDIU52/ref=sr_1_3?ie=UTF8&qid=1522783482&sr=8-3&keywords=ge+smart+motion+sensor
Yup... be worried about how to pay for a new house when your insurance claim is denied because you attached a non-UL listed device into the mains wiring.
Instead, buy [something like this] (https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC) and make sure the installation's done to code.
Your device will be cheaper and more customizable. But you shouldn't screw around with mains power unless you know what you're doing both in terms of the electric and the legal aspects.
Battery powered motion lights? Would have to change batteries as needed. Not stylish enough maybe (although being a new parent, learn that function is going ot have to overtake fashion real soon)
Motion light bulb? No batteries, but requires you leave the light switch on. Also likely dependent on the fixture you have in the hall. There are options on entire new fixtures, too, which probably look better (or at least less obvious), but a little bite more work to install.
Motion ligh switch. Would only work if you are near the switch, though (not sure what "easy access in the dark" means). You could install this yourself, its 3 or 4 wires tops.
Motion may not be the way to go if you have pets
I have three of these GE sensors and can vouch for the detection range. Haven't had issues with false positives. I heard battery can be an issue, but I plug these into a micro-USB charger and they work just fine. I use them with Home Assistant, which technically works requires a little more setup in reading values (it's not a simple on/off state).
Amazon link for reference: https://www.amazon.com/GE-Wireless-Activation-Monitoring-34193/dp/B01KQDIU52
You can sometimes find deals on eBay for $25 during the 20% off coupon periods. I try not to pay more than $28 for these.
Replace your light switches with motion sensor switches, like this one...
https://www.amazon.com/Hykolity-Occupancy-Neutral-Required-White-Pack/dp/B077VN4YK7/ref=sr_1_6?s=electronics&ie=UTF8&qid=1525352554&sr=1-6&keywords=motion+sensor+light+switch
I did something like that for my Lego shelf. Used some LED strips and a motion sensor module to keep it all automatic. I had no idea what I was doing and bought a bunch of stuff I didn't need, but...
And if you're comfortable soldering, that's pretty much all you need to get something up and running. But I wanted to make it all modular so I could take it apart and set it back up without too much hassle. So I ended up buying adapters and coaxial power cable things:
I'm pretty sure I did it as inefficiently and cost ineffective as possible because I have severe amazon impulse control issues and just buy shit to get started on fun projects. I'm sure with a little more research/guidance you could do it a little cheaper. But I'm happy with my setup for now.
and here's a picture of the shelf. The shelf is terrible, and it's all a wreck because I'm in the middle of moving, but it shows the brightness pretty well. Oh and I have about a 1/4 roll of LEDs left, so I'd guess 2 or 3 rolls would take care of your shelf.
That sounds expensive, I can think of a few ways to do it but I'm sure you don't want to spend that amount of money!
Just an idea, I would install a motion sensor for the garage lights in the existing switch.
[if you have 2 switches controlling the lights ](Lutron Maestro Motion Sensor switch, no neutral required, 600 Watts Single-Pole/Multi Location, MS-OPS5M-WH (1 Pack), White https://www.amazon.com/dp/B005WM3C42/ref=cm_sw_r_cp_api_Q43Jyb6PWZE72)
[if you have 1 switch connected ](Leviton IPS02-1LI 300-Watt Incandescent, 150-Watt LED/CFL Occupancy Sensor (Auto ON/Auto OFF), Single Pole, Ivory https://www.amazon.com/dp/B00BUZQWBK/ref=cm_sw_r_cp_api_I53JybXH1684X)
Be sure to go with a name brand or anything that is UL listed. It's not cost effective to go cheap on the sensor as it would only be $5 more for something UL listed.
Good luck!
I had similar intentions with my laundry room at one point, so I understand where you are coming from, but you might re-consider a simple occupancy switch (https://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=sr_1_1?ie=UTF8&qid=1485316261&sr=8-1&keywords=MS-OPS2-WH). For me, the more I thought about it, the more I realized involving my HA system was simply making things more complicated than they needed to be for what I wanted to do.
and can use a Philips Hue motion sensor. https://www.amazon.com/Philips-Motion-Sensor-Installation-Free-Exclusive/dp/B01KJYSOGI/ref=pd_sim_60_2?_encoding=UTF8&psc=1&refRID=82E68N6TNWRSAWM3E3VZ
May I suggest the GE Portable Motion Sensor?
On sale for $28 right now on Amazon, runs off battery and USB power which helps if it is in a high-traffic area. I have one and use it for my kitchen when I arrive home to flip a few lights on as well. It is fairly quick and SmartThings has it integrated into their hub.
I'll run that by the wife and see what she thinks. If I did that, I would just replace the current switch with the sensor, wiring the sensor exactly as the switch is wired, correct?
Something like this:
http://www.amazon.com/Leviton-ODS10-ID-Decora-277-Volt-Occupancy/dp/B0007N72P6/ref=sr_1_3?ie=UTF8&qid=1393903213&sr=8-3&keywords=Occupancy+Sensors
I would use this one [here, and LOOK at all of the colors!!]
(http://www.amazon.com/Lutron-MS-OPS5M-WH-Maestro-Single-Occupancy/dp/B005WM3C42)
Is there anywhere other than the UK Amazon product page that mentions the limitation to Bridge 2.0? I can't seem to find it anywhere on Phillips' Hue product page, nor the US Amazon page:
https://www.amazon.com/Philips-464610-Hue-Motion-Sensor/dp/B01KJYSOGI/ref=sr_1_1?ie=UTF8&qid=1474321497&sr=8-1&keywords=hue+motion
http://www2.meethue.com/en-us/motion-sensor/
I like these because you can still easily turn the lights off when you're done.
https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=sr_1_3?ie=UTF8&qid=1550262593&sr=8-3&keywords=lutron+motion+switch
try this
I have a few vives, both are connected to systems that do not have bluetooth. I had one axis on one of the lighthouses go out and had to replace it, I had just left it on all the time. HTC recomends turning them off when not in use. I never remembered to shut them off so I added a motion detection switch. http://imgur.com/a/TgSRo . Works well, uses the same size connector as the vive's DC connector so it is easy to install, has 120 degree FOV stays on for 7 and a half minutes since the last motion was detected in the room so if won't turn off if you leave the room for a few minutes. It was nice to discover that the neither the IR light or vibration seems to interfere with both working properly. The switches a pretty cheap at $6 each, https://www.amazon.com/Kang-Automatic-5V-24V-Infrared-Motion/dp/B010LGB6M8/ref=pd_sim_60_2/152-1989448-0618943?_encoding=UTF8&pd_rd_i=B010LGB6M8&pd_rd_r=HK445EGTJZB4KDDTQ315&pd_rd_w=x1MlX&pd_rd_wg=figen&psc=1&refRID=HK445EGTJZB4KDDTQ315
He means a non-SmartThings one, like this one
https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=sr_1_3?ie=UTF8&qid=1498060276&sr=8-3&keywords=motion+sensor+switch
Here's one for $15
I just did under (and in) cabinet lighting with these. I soldered and shrink wrapped all the connections, and put in motion sensors for the in-cabinet ones. The whole project was < $100.
Making Hue lights usable by the rest of the family is definitely a concern. You have a couple of easy options:
Depending on your specific needs you'll probably want to use a combination of these things.
The dimmer switches work well, you can press the On button repeatedly to pick between 4 scenes, and then change the brightness of a scene once it is set.
I just started playing with the motion sensor and it's definitely nice to have the lights respond without having to explicitly turn them on and off, but not everything will make sense to be triggered by motion.
I also find myself frequently using Alexa to control the lights. The main consideration here is that you will need to group your lights into rooms and make sure everyone in the family knows what the names of the rooms/lights are. Alexa has the ability to set light brightness, set a specific color, or change to a Hue scene. It's fairly flexible.
Eventually you'll want to get fancy and set up a home automation hub like SmartThings or HomeAssistant to let you bring in devices from multiple ecosystems (Hue, Arlo, etc) and create automation rules to run everything, but for now it sounds like you'd be happy with a few of the Hue accessories to make the lights easier to control. Good news is that Hue is designed to be user-friendly and all of the options I listed will let you do basic control pretty easily. When you outgrow that, you have more advanced options available to you.
Hope it helps, and let us know if you have any specific questions about how to set stuff up.
You’re talking about a jamb switch, but they don’t meet energy codes in my area. The issue that municipalities have with jamb switches is that if you don’t close the door then the light never goes off. If you put in a motion sensor with an automatic off then it will go off after a certain amount of time even if you don’t close the door. That’s really the best option. Technically motion sensors indoors don’t meet CA energy codes either because they don’t want lights automatically turning on anywhere in the house. They want you to physically hit the switch and then for it to time off. That is called an occupancy sensor. It’s actually required in closets and bathrooms.
But what you’d want is something like this: https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/ref=mp_s_a_1_5?adgrpid=58685001040&amp;gclid=EAIaIQobChMIhfvT7I7-5AIVoyCtBh20jwIxEAAYASAAEgJHu_D_BwE&amp;hvadid=274898185342&amp;hvdev=m&amp;hvlocphy=9032130&amp;hvnetw=g&amp;hvpos=1t1&amp;hvqmt=e&amp;hvrand=11606527727516147700&amp;hvtargid=kwd-296546370640&amp;hydadcr=12164_10197800&amp;keywords=switch+motion+sensor&amp;qid=1570037880&amp;sr=8-5
This is what I have in my laundry room.... Looks like they have an LED Dimmer version now too. I'm considering getting that for the bathroom...
Lutron Maestro Motion Sensor Switch, No Neutral Required, 250 Watts, Single-Pole, MS-OPS2-WH, White https://www.amazon.com/dp/B005WM3ALC/ref=cm_sw_r_other_apa_i_M1MUDbYY3A2DX
Sorry for the late reply. Here's the one I used. I think it requires that your home is wired with a neutral wire. There are probably some out there that don't require that if you don't have neutral.
&#x200B;
https://www.amazon.com/gp/product/B0731PPJYD/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
&#x200B;
E: The best bet is to find areas where you want the light to go on no matter what AND that the switch is in a place where it won't switch on when you don't want it to. For example, I have one in my garage, in my laundry room, in a weird hall where the switch is on the other side of the room from where I normally walk in and on a single light in my kitchen (this is so only one light goes on in the kitchen goes on in case I'm up in the middle of the night and need just enough light to move around or enough light to find the other switches), and in a couple of closets. They have adjustable sensitivity and an adjustable timer, so in some cases, I have it really sensitive and others not-so-sensitive. And, for instance, in my laundry room, I have it so it turns off after one minute of not detecting motion, so I never have to touch the laundry room switch and it turns on when I walk in and off one minute after I walk out with an arm full of clothes.
https://smile.amazon.com/gp/product/B005WM3ALC/
Complex to set up, but works great!
Have you considered a motion sensor?
This PIR motion sensor is rated at 6 amps, 12-24 vdc, has adjustable timer and might be easier to install than a limit switch.
KISS Keep It Simple, Stupid. :-)
An automated closet/pantry light, typically, doesn't need to be smart. You don't need to turn it on or off at certain times. You don't need notification it was turned on, off, or left on. You simply need it to be motion or switch/timer activated/deactivated.
I understand you had the additional task of wiring electrical for this, but anyone with an existing lighted pantry or closet, think why it would need to be smart before you spend money on fixtures for it. Most of the time, you merely want it to turn off because people forget to do that.
Door-jamb closure switches are an option, unless you're dealing with people who not only leave on lights but also don't close doors. However, there is some drilling and electrical work required to install those. In my experience, they're often installed on the hinge side of the door, which is opposite where the light switch is located.
Lutron's Maestro Occupancy/Vacancy Sensors are, IMO, a perfect solution for this if your closet is already lighted. They can be configured to turn on with motion (occupancy mode), or switch press (vacancy mode); configured to stay off if there is already enough light; and configured how long to stay on after motion has stopped. I've placed these in ALL closets.
In bathrooms, however, I did opt for smart switches and motion sensors, for both fans and lights. The fans are programmed to come on with a switch-press, and turn off after 60 minutes of no motion. The lights are programmed to turn on with motion, but at different light levels depending on time ... and off again after 10 minutes of no motion. I could have opted for in-wall timers for the fans, but decided to go with smart switches instead.
Yes, thats possible.
Basically, you're setting up a rule in Smartthings under the "Smart Lights" smartapp that says, turn on <GE switch> when motion is detected with <motion sensor>.
Alternatively, I would recommend using Lutron motion sensor (https://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC). It's just cheaper and does the same thing.
While I do have plenty of GE zwave switches and Hue bulbs throughout my house, I have those Lutron motion switch in my garage, pantry, laundry room, bathrooms, etc.. I dont need those rooms to be smart--just need to turn on when motion is detected.
edit: missed the part that said the switch is inside the house. The first option is best for your use case.
I used these. They work great so far!
http://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC?ie=UTF8&amp;psc=1&amp;redirect=true&amp;ref_=od_aui_detailpages00
This is similar to what i use. Works perfectly.
This worked on a hall closet build I did. https://www.amazon.com/dp/B00HJ6ZZBM
Not what you're for but have you considered GE Z-wave battery/USB motion sensors?
I had not considered a 3 way motion sensing light switch. I had just found this one on amazon. I think I will give this a try. Now to hope that the one by itself is the master and not the slave. I don't want to deal with the box that has 3 switches in it.
I found this: GE Enbrighten Z-Wave Plus Smart Motion Sensor. It has a USB or battery.
https://www.amazon.com/GE-Wireless-Activation-Monitoring-34193/dp/B01KQDIU52
Is it in a pantry or closet or something? If not why not put in a motion sensor on the switch itself? Our company uses these and they are nice: Link
I'm not sure if the reduced brightness dusk-to-dawn would be possible with any device, but here is a motion sensor that you would just mount on the wall outside your garage: Link to Amazon
Hi! If you're a big DIY person, I found these companies on Amazon called Top Greener and Enerlites where you can install your own light switches. The one that I have all around my house are motion sensor switches and the fan/light timer. So far, I've noticed my bill has gone down. I think it's good because when you program the lights, they basically turn off themselves. Anyway, I'll provide the links if you're interested so you can make a better decision.
https://www.amazon.com/Enerlites-Programmable-Lighting-Vacation-Daylight/dp/B00TSU5GB6
https://www.amazon.com/TOPGREENER-TSOS5-W-Single-Pole-Fluorescent-Incandescent/dp/B015G8VLNA
https://www.amazon.com/Enerlites-Countdown-Ventilation-1-5-10-15-20-30-REQUIRED/dp/B00IB0ZJXE
GE makes a ZWave motion dimmer that works well: https://www.amazon.com/GE-Occupancy-Required-SmartThings-26933/dp/B071Y38FX5/
However, all of those locations you listed might work just as well with "dumb" motion switch: https://www.amazon.com/TOPGREENER-TSOS5-W-Occupancy-Override-REQUIRED/dp/B01M01SVG9/
Lutron has battery powered (10 year batteries) occupancy sensors that you stick to the ceiling in the closet and then pair it with any of their clear connect switches or dimmers (like Caseta, Maestro RF, etc.). It's not cheap but it's made for jobs where the switch is outside but you want motion inside.
I used these for all motion sensor switches and these for the humidity sensor fan switches.
Have you considered motion sensor switches? I tried the smart switch route but found no neutral and switched to using motion sensor switch instead.
https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC
I have two choices for you.
If you have a neutral, this one has the motion sensor in the switch and uses IR and ultrasound:
Leviton OSSMT-MDW Ultrasonic/Infrared, Dual-Relay Multi-Technology Wall Switch sensor, 2400 Sq. Ft Major & 400 Sq. Ft Minor Motion Coverage, White https://www.amazon.com/dp/B003DA4NY8/
Don't have a neutral? Or the switch isn't in a good place to detect motion? No problem:
Buy a motion sensor:
Lutron LRF2-OCR2B-P-WH Radio Powr Savr Wireless Ceiling-Mounted Occupancy/Vacancy Sensor, White https://www.amazon.com/dp/B005LPET0G/
And a switch it will pair to:
5 Amp Max. 2 Button RF Switch - 120/277V White - Lutron PD-5S-DV-WH https://www.amazon.com/dp/B00NCEMBIA/
This switch doesn't require a neutral.
Do you have a switch in the closet? Or just power for a light like a pull chain?
If you have a switch, install a motion sensing light switch
If you just have a pull chain/bare socket...install one of these
Does each area have its own switch? If so, forget automation with door sensors. Grab a PIR switch, such as
http://www.amazon.com/Lutron-Maestro-required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC
No reason to over complicate it
Many have a switch to choose on, auto, off. https://www.amazon.com/TOPGREENER-Occupancy-Single-Pole-Fluorescent-Incandescent/dp/B07B8V8CD7
You could try something like this. I've never used it, but I saw this old house use something similar in an old house with the same problem.
Wireless Light Switch Kit, COLEMETER Remote Light Switch - Battery-FREE (Self-powered), No Wiring, No WiFI - 100-500ft Indoor/Outdoor Remote Control Light Switch Pair up with Transmitter https://www.amazon.com/dp/B071H6T3MV/ref=cm_sw_r_cp_apa_ALX6BbRH57P3V
It's not really smarthome, but lutron makes switches that do that. It's the vacancy option.
Basically they have two settings. Occupancy will turn lights on when they detect motion. Vacancy requires you to turn them on, but turns them off after a period of no motion.
Lutron Maestro Sensor switch, 2A, No Neutral Required, Single-Pole, MS-OPS2-WH, White https://www.amazon.com/dp/B005WM3ALC/ref=cm_sw_r_cp_apa_smS7Bb8Q8CAKA
If you do not need it to be IOT connected these lutron occupancy sensors work extremely well. They have different settings and you can set it so that it turns on manually but turns off after a slightly Variable set time no motion.
https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/
If you have a zwave hub this GE switch has the proper modes to turn off but not on.
GE Z-Wave Plus Smart Lighting Control Motion Sensor Dimmer Switch, In-Wall, Vacancy / Occupancy Sensor, White & Light Almond Buttons, Zwave Hub Required- Works with SmartThings Wink & Alexa, 26933 https://www.amazon.com/dp/B071Y38FX5
If you don’t want it to integrate with a hub, the below can do what you want in the proper mode.
Lutron Maestro Sensor switch, 2A, No Neutral Required, Single-Pole, MS-OPS2-WH, White https://www.amazon.com/dp/B005WM3ALC
These kind of switches are called occupancy sensor switches. Here is an example of one
Maxxima Occupancy Vacancy Motion Sensor PIR Wall Switch, Wall Plate Included https://www.amazon.com/dp/B0731PPJYD/ref=cm_sw_r_cp_apa_uBI7Bb11C3K4V
I want something like this https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC
your problem can be solved for $15.24 with free shipping
Easy... replace your light switch with one of these: https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC
I believe it has different sensitivity adjustments, so you might be able to turn down the sensitivity enough to where it ignores your cat but picks up your movement.
I just installed a [Lutron occupancy sensor switch] (https://www.amazon.com/Maestro-Required-Single-Pole-Multi-Location-MS-OPS5MH-WH/dp/B005WM3C42/ref=dp_ob_title_hi) in the kids' bathroom - the one switch is connected to both the fan circuit and light circuit in the switch box.
I have it set to turn on when the button is pressed, and either turn off 20 minutes after motion is detected or button press off. I originally planned on two switches, but after talking with some guys they suggested that if I want the kids to turn the fan on to just wire it in line with the lights - otherwise they won't bother with turning the fan on.
Yea it's pretty standard for that time period. People will still do it now. Basically the "feed" is at the light location and they ran a single Romex cable to the switch location. Switch boxes were smaller back then so it was even more motivation to do it that way so less wires would be at switching locations.
You can either find an occupancy sensor that doesn't require a neutral to operate like this or rewire.
would this work?
https://www.amazon.com/dp/B005WM3ALC/ref=cm_sw_r_cp_apa_uK9azbEYSWR72
About $100:
In my 30 seconds of googling, Occupancy sensors looks like what I want.
I like these http://www.amazon.com/Lutron-MS-OPS2-WH-Maestro-Single-Occupancy/dp/B005WM3ALC
unless someone has a better idea.
Use a multimeter to test for ground.
Or test the sensor by installing in a different location.
Or install a sensor that does not need ground.
I thought the IPS02 didn't require ground.
But this one does
https://www.amazon.com/Lutron-MS-OPS5M-WH-Single-Pole-Multi-Location-MS-OPS5MH-WH/dp/B005WM3C42/ref=sr_1_25?keywords=motion+sensor+switch&amp;qid=1571782494&amp;sr=8-25
The quickest simplest option to use a PIR would be something like this. Plug and play, almost nothing to do except plug in a suitable power supply and make sure your LEDs have the correct plug.
You could also do the same with an Arduino and a relay module, you could then use the pressure switch or PIR as input. The Arduino could also be omitted and the pressure switch or PIR connected directly to the relay module providing you choose a relay module with the coil drive transistor on board but if you use the pressure switch without an Arduino you will have whats called switch bouncing, basically it would cause the relay/lights to flicker as the switch makes and breaks contact, you can "debounce" the switch with code in the Arduino quite easily and add other features such as a cool off period before it can be activated again, there are many other ways to debounce a switch but without getting into electronics too deeply an Arduino is the simplest. PIR modules have an "on time" which can be adjusted with a potentiometer from a second or so to many minutes so switch bounce isn't a problem with a PIR.
Your pressure switch option regardless of the way u/debug_yourself is carrying on would work fine providing the current is kept low, like less than half an amp, if you need more than that it would be best to go with the relay option.
Very easy - Amazon ships them at the normal price plus $7 postage
Philips Hue Smart Motion Sensor (Installation-Free, Exclusive for Philips Hue Lights) https://www.amazon.com/dp/B01KJYSOGI/ref=cm_sw_r_cp_api_nOFOzbYSC74R4
Both of your examples are good examples of overthinking things, in my opinion. I bet you have switches on both sides of your family room - on one side, you can get to the dining room lights and on the other, to the kitchen lights. So if you have one central "fancy" switch, now what - you're going to manage your kitchen lights on the way from the dining room? It's ok to use a regular switch when it makes sense. And your basement example is almost identical to my front entrance and all I did was put in a motion sensor switch and now the lights turn on when I open the door and turn off after a few seconds of no motion (that config won't work for basement but you can get one that turns off at the top with a physical switch). Something like this (not exactly what I have) - https://www.amazon.com/dp/B005WM3ALC/
If you want to use SmartThings AND just want to turn lights on/off with motion, I don't see a need for wired sensors.
If you really want wired sensors (because of battery/network concerns), I doubt SmartThings would be the best choice for your platform. You'd need an extra device that would receive then sensor communication and then it would need to relay that to SmartThings. I don't think there's much "off the shelf" options for this, except maybe ADT. I'm sure there's some custom options you could build with a PI or other board but then you get into major customization/time/effort. But, some others on the sub may know of some more options.
You may want to check out some more "professional" HA platforms besides SmartThings.
edit: This GE zwave sensor will accept wired USB power.
TOPGREENER TDOS5 Motion Sensor Light Switch, 500W Incand LED CFL 1/8HP, Free Wall Plate, NEUTRAL REQUIRED, 2 Pack White https://www.amazon.com/dp/B01DYJIR4E/ref=cm_sw_r_cp_apa_HAdAybT9MGV71
Is that what your looking for? My work uses them. They work well but if u sit still to long they may turn off on you.
I've put these in rooms I use the most & they are great.
Something like these. Lutron Maestro Sensor Switch, 2 Amp, No Neutral Required, Single-Pole, MS-OPS2-WH, White https://www.amazon.ca/dp/B005WM3ALC/ref=cm_sw_r_cp_apa_i_TGBUDbAGK76S9 (note the Canadian prices)
Maybe an ifttt to turn on a bedroom light when motion is detected. (Requires a $35 D-Link Motion Sensor, not sure if it'd work with the $40 Phillips Hue Motion Sensor.)
I have that motion light thing in my garage, it works when it wants to, it has several blind spots.
I'd go with something like this
http://www.amazon.com/Lutron-MS-OPS2-WH-Maestro-Single-Occupancy/dp/B005WM3ALC/ref=sr_1_1?ie=UTF8&amp;qid=1381036151&amp;sr=8-1&amp;keywords=lutron+motion+sensor+light+switch
I have that in my laundry room and it is way more reliable.
Does it need to be time-of-day, or could it be based on a light sensor?
There are replacement wall switches with an embedded "occupancy sensor" and ambient light override.
> Hue motion sensors
These ones on Amazon? They're $40 each plus need I'd need a new hub for another $45. I've heard good things about Hue reliability but the price and limited utility makes that not very compelling to me.
I've been very happy with the zwave plus GE motion sensors: https://smile.amazon.com/GE-Wireless-Activation-Monitoring-34193/dp/B01KQDIU52
Love that the can be USB powered or battery. And are configurable for reset time and sensitivity.
This explains why you can install an IR wall switch only rated for 800W like this UL listed one -
https://www.amazon.com/Maxxima-Occupancy-Vacancy-Motion-Included/dp/B0731PPJYD/ref=sr_1_5?ie=UTF8&amp;qid=1525551335&amp;sr=8-5&amp;keywords=motion+sensor+light+switch+ul
Use this: https://www.amazon.com/Lutron-Maestro-Required-Single-Pole-MS-OPS2-WH/dp/B005WM3ALC/
You can set how long it turns off after it is turned on and stops sensing motion to 10 minutes. Much easier and cheaper than getting a zwave switch + motion sensor or similar.
Actually, if you already have a light install something like this:
https://www.amazon.com/gp/product/B005WM3ALC
$20 solution that is a motion sensor for your closet light, best thing I've ever done. I can walk into the closet, light comes on, then goes off after 60 seconds to 10 minutes depending on the setting.
I'm actually sort of leaning towards this now" http://www.amazon.com/gp/product/B00HJ6ZZBM?psc=1&amp;redirect=true&amp;ref_=ox_sc_act_title_1&amp;smid=A3SY4WN81ZEM06
Seems pretty straight forward and would work just as well. When I open the cabinet doors I'd only need to be able to see the battery stats for a short moment. Then when I shut the doors it should turn off automatically. That's similar to the depressed switch as you mentioned.
Thoughts or anything I may have over looked?
Honestly if all you are wanting is the lights to turn on when someone walks in the room you may be better off not going with a smart solution. You can do what you want with Hue bulbs.
There are also a number of bulbs with motion sensors built in. I've never used one personally, so I'd do more research to see how it knows when to turn off.
https://top10perfect.com/top-best-motion-sensor-light-bulbs-reviews/
But your best and cheapest solution might be this.
https://www.amazon.com/gp/aw/d/B005WM3ALC/ref=mp_s_a_1_1?ie=UTF8&amp;qid=1486211121&amp;sr=8-1&amp;pi=AC_SX236_SY340_QL65&amp;keywords=vacancy+sensor+switch&amp;dpPl=1&amp;dpID=31E-2BSEFmL&amp;ref=plSrch
I know you said you were worried about messing with wiring, but honestly in most homes (I'm assuming you are in America, excuse my assumption if you are not) to change out a switch you literally turn off the breaker that switch is on, unscrew the cover, take out two more screws that hold the switch against the wall and then there are two wires going to the switch. Take those out and put them in the new switch and reverse the process. It is insanity simple in most cases.
Anyways, hope that's helpful. Let me know if you have any more questions.
What about installing two of these, one at the top switch and one at the bottom? https://www.amazon.com/gp/product/B005WM3ALC/ref=oh_aui_detailpage_o09_s01?ie=UTF8&amp;psc=1
Then, configure the setting to turn on by motion but turn off after 1, 5, or 15 minutes if no movement is detected. You can still press the button to manually turn on if needed.
Under cabinets look great (as you noted), and work great when they are on.
&#x200B;
I think the reason people don't use them is because they are not typically wired to a switch on old houses; and/or hot bulbs overheat and damage themselves.
&#x200B;
The solution is LED lights, triggered by a sensor like this or this that turn them on and off for you. LED don't overheat much, and the sensor turns them off, and on, for your convenience and safety.
I have a standard lutron occupancy sensor switch by the entry door of my fairly sizeable three car garage and it works perfectly. I just used it as a drop in replacement for the light switch that was already there. Turns the lights on when a door opens, turns them off after you leave.
Edit: Specifically I'm using this one: http://www.amazon.com/gp/aw/d/B005WM3C42/ref=dp_ob_neva_mobile
I picked the non dimmer version since it's controlling six large florescent lights down the length of the garage.
Unless you want redundancy, your thermostat can be your freeze sensor. The ecobee will send out temperature notifications and it also supports high/low thresholds on IFTTT if you're into that.
Also, look into motion sensing light switches. I use them in bathrooms and closets and they suit me well. They're a pretty cheap way to get some additional convenience.
http://www.amazon.com/gp/product/B005WM3ALC?psc=1&amp;redirect=true&amp;ref_=od_aui_detailpages00
I feel like this is easily solved using a passive infrared sensor. I use one for turning on spill lights under the bed at night, and it's solving for the same constraints (low power draw; turns on when some*one* walks by, rather than objects). It's adjustable for range, ambient light, and delay.
What I'm using: Amazon (non-affiliate code link)
Since you don't feel like running a few feet of 14/3 NM and installing 3-way switches (which would be the right way to do what you wanna do), just use an occupancy sensor.
Thanks for the help.
I'm trying to install this --> https://www.amazon.com/White-Motion-Sensor-Light-Switch/dp/B0799QTXX5/ref=sr_1_4?keywords=sensor+switch&qid=1562792145&s=hi&sr=1-4 . Its wired for a single pole switch.
The current set up is using two three way switch. So one of the switch doesn't have a direct hot line from the power/panel box.
Any who, I figured it out. I can use one of the travelors from the current circuit to supply power to the sensor switch that didn't have a direct hot line to the power/panel box.
Mirror defogger: never struggle to use the mirror after showering. Radimo MD18x26 Mirror Defogger Pad Rectangular 18-Inch By 26-Inch , 120-volt https://www.amazon.com/dp/B00B7L0L64/ref=cm_sw_r_cp_api_i_7lqnDbHP1J3DG
Garage motion-sensing light switch: Never forget to turn it off once you are in the car, or have to turn it on with hands full: Lutron Maestro Motion Sensor Switch, No Neutral Required, 250 Watts, Single-Pole, MS-OPS2-WH, White https://www.amazon.com/dp/B005WM3ALC/ref=cm_sw_r_cp_api_i_onqnDbVA4M1K6