Best tool trays according to redditors
We found 151 Reddit comments discussing the best tool trays. We ranked the 60 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 151 Reddit comments discussing the best tool trays. We ranked the 60 resulting products by number of redditors who mentioned them. Here are the top 20.
I bought a set of these wrench organizers which worked fantastically for me since they're magnetic on the bottom. I also have one of these plier racks for my pliers drawer (takes a taller drawer to fit) but it holds everything in place really well. I also can't recommend enough the hansen socket trays as they work better than any other socket organizer i've seen so far. I also have something similar to this hand tool organizer that holds most of my screwdrivers and picks.
my toolbox is still in a state of flux so I can't really shadow my tools like /u/skiman13579 suggests, even though i'd love to.
organization will set you free.
magnetic socket tray will change your life but I was a mechanic for many years so maybe I'm biased.
I have more of those than I can count. While you're at it, get one or two of these. Way better than a pincushion in my opinion. Bonus if you have a metal machine because they stick.
I got it on amazon. This one is 30" wide and holds 32 tools, but they have shorter ones also.
https://www.amazon.com/gp/product/B00SA23E80
I am a huge fan of these.
If you don't want to spend the money on new foam you can buy cheap camp sleeping pads from Walmart. Here's my field kit / with the walmart pads.
All great suggestions so far. Since they will be mobile stations I would add some magnetic parts trays to prevent lost screws.
Mind if I ask what kind of place this is that gets to build various sizes of multicopters? Can you give any details about the builds and how they will be used?
Not op, but its nice that it comes with the wheels installed. Wish that there were swivel casters only in the middle and handle end.
The top drawer is able to hold hansen socket trays 1/4 through 1/2, also able to hold [this pliers organizer.](https://www.amazon.com/gp/product/B00SA23E80/ref=ppx_yo_dt_b_asin_title_o01__o00_s02? ie=UTF8&psc=1)Still getting my garage in order and tools transferred from my smaller craftsman boxes. I'm liking it so far, one small gripe is that the long top drawer cant be pushed in from the corners, you have to push it in from a couple inches in.
Adobe products care more about frequency then about number of cores.
You do not need anything specific to build a PC. If you want to make it easy on yourself, get a magnetic screwdriver with a magnetic pickup tool. The long and thin pickup tool will help you retrieve screws that wander into cracks.
GreatNeck SD7C 8-in-1 Screwdriver with Magnetic Telescoping Pick-Up Tool
Dropping screws is inevitable, so avoid working over carpet. If you do drop a screw on carpet, sweep the pickup tool over the area slowly. The tip magnet will grab it off the surface. You could get a magnetic tray to reduce the chance of drops.
Titan Tools 11061 Mini Magnetic Parts Tray
While some people suggest a grounding wristband to dissipate static, I think they are a waste for PC building. Just plug in your power supply and touch it each time you come to the workplace. A powerstrip with an off switch can be used, if your power supply does not have a physical power switch on the back.
I would suggest you watch another couple PC builder videos.
How To Build a $800 Gaming PC in Late 2018
How To Build a $500 ITX Gaming PC in 2018
I would also suggest this post-POST video:
First Five things to Do with a New Computer
PCPartPicker part list / Price breakdown by merchant
Type|Item|Price
:----|:----|:----
CPU | AMD - Ryzen 5 2600 3.4 GHz 6-Core Processor | $228.00 @ Powertop
Motherboard | *ASRock - B450M PRO4 Micro ATX AM4 Motherboard | $79.90 @ Vuugo
Memory | *G.Skill - Ripjaws 4 Series 16 GB (2 x 8 GB) DDR4-3000 Memory | $129.99 @ Newegg Canada
Storage | *Western Digital - Black NVMe 500 GB M.2-2280 Solid State Drive | $119.99 @ Memory Express
Storage | *Seagate - Barracuda 2 TB 3.5" 7200RPM Internal Hard Drive | $67.95 @ Vuugo
Video Card | *Gigabyte - Radeon RX 570 8 GB GAMING 8G Video Card | $199.99 @ Memory Express
Case | *Inwin - 301 White MicroATX Mini Tower Case | $99.99 @ Memory Express
Power Supply | *EVGA - BR 450 W 80+ Bronze Certified ATX Power Supply | $29.99 @ Canada Computers
Case Fan | Noctua - NF-A12x25 PWM 60.1 CFM 120mm Fan | $37.90 @ Amazon Canada
| | Total (before mail-in rebates) | $1043.70
| | Mail-in rebates | -$50.00
| Total | $993.70
| | *Lowest price parts chosen from parametric criteria |
.
PCPartPicker part list / Price breakdown by merchant
Type|Item|Price
:----|:----|:----
CPU | *Intel - Core i3-8350K 4 GHz Quad-Core Processor | $224.99 @ Amazon Canada
CPU Cooler | *Deepcool - GAMMAXX 400 White 74.34 CFM CPU Cooler | $48.33 @ Amazon Canada
Motherboard | *MSI - Z370M GAMING PRO AC Micro ATX LGA1151 Motherboard | $210.99 @ Amazon Canada
Memory | *G.Skill - Ripjaws 4 Series 16 GB (2 x 8 GB) DDR4-3000 Memory | $129.99 @ Newegg Canada
Storage | *Western Digital - Black NVMe 500 GB M.2-2280 Solid State Drive | $119.99 @ Memory Express
Storage | *Seagate - Barracuda 2 TB 3.5" 7200RPM Internal Hard Drive | $67.95 @ Vuugo
Video Card | *Gigabyte - Radeon RX 570 8 GB GAMING 8G Video Card | $199.99 @ Memory Express
Case | *Inwin - 301 White MicroATX Mini Tower Case | $99.99 @ Memory Express
Power Supply | *EVGA - BR 450 W 80+ Bronze Certified ATX Power Supply | $29.99 @ Canada Computers
Case Fan | Noctua - NF-A12x25 PWM 60.1 CFM 120mm Fan | $37.90 @ Amazon Canada
| | Total (before mail-in rebates) | $1190.11
| | Mail-in rebates | -$20.00
| Total | $1170.11
| | *Lowest price parts chosen from parametric criteria |
I did this on my Epi SG Jr earlier this year and it’s a game changer. Definitely go for it. I love the Kluson “Safety Post” tuners on my Jazzmaster so I bought a set of those ($42 on Reverb) — just be sure whatever you buy is 3x3 and not 6-in-Line.
If you’re reasonably comfortable with basic tools it’s an easy upgrade. I posted notes and pictures if that’s helpful. The basic steps:
https://www.amazon.com/gp/aw/d/B001C6NL52/ref=mp_s_a_1_3?ie=UTF8&qid=1501519580&sr=8-3&pi=AC_SX236_SY340_QL65&keywords=socket+organizer&dpPl=1&dpID=51-8Yw7rjDL&ref=plSrch
I've been using these and haven't looked back at using those cheap socket rails. Those things always pissed me off and never held sockets on very well, these plastic racks just let the sockets sit on a plastic pin and you can use them like a tray and put the whole thing in your service cart and it keeps everything handy
5 1/8" by 3 5/8". Height is 1 1/4"
I picked up one of these yesterday. You can stack 3 Falcons high if you wanted: https://www.amazon.com/Stack-DCY-10-Parts-Storage-Organizer/dp/B00Z1K625Q
A better question is what on the ladder is magnetic? Aren't most ladders either aluminum or fiberglass and non-magnetic?
What about including a magnetic tray, such as this Titan Tools Mini Magnetic Parts Tray on Amazon (cheaper than alternatives at McMaster). But even then, you run into the same problem, what is magnetic that you stick this tray to?
They are called Hansen Socket Trays. I think he got his at Harbor Freight but just about anywhere that sells tools should carry them.
I seriously could not work at a bench now that didn't have a magnetic bowl sitting on the back of the vise. It helps so much.
https://www.amazon.com/gp/aw/d/B001C6NL52
You can also buy singles, instead of the whole set.
Looks like the rails from the Ernst socket boss kit, minus the tray that holds the rails. I have this set for my sockets. https://www.amazon.com/dp/B00CHJHA8W/ref=cm_sw_r_other_apa_i_C-m5Ab4ADCXCQ
These are my favorite - they come in various sizes and colors:
http://www.amazon.com/Lisle-40200-Magnetic-Socket-Holder/dp/B0002STSTY
Northwest of England! I pray you're a Manchester United fan? Glory glory Man United!
Anyway, enough about football. Here's a build (with everything you'll need) as well as some useful videos.
PCPartPicker part list / Price breakdown by merchant
Type|Item|Price
:----|:----|:----
CPU | AMD - Ryzen 5 1600 3.2GHz 6-Core Processor | £185.95 @ Amazon UK
Motherboard | MSI - B350M GAMING PRO Micro ATX AM4 Motherboard | £73.77 @ Box Limited
Memory | Corsair - Vengeance LED 16GB (2 x 8GB) DDR4-3000 Memory | £136.77 @ Amazon UK
Storage | SanDisk - SSD PLUS 240GB 2.5" Solid State Drive | £74.99 @ Amazon UK
Storage | Seagate - BarraCuda 1TB 3.5" 7200RPM Internal Hard Drive | £35.99 @ Aria PC
Video Card | MSI - GeForce GTX 1060 6GB 6GB GAMING X Video Card | £293.48 @ BT Shop
Case | Phanteks - Enthoo Evolv TG (Silver) MicroATX Mini Tower Case | £111.09 @ Box Limited
Power Supply | Corsair - CXM 450W 80+ Bronze Certified Semi-Modular ATX Power Supply | £47.57 @ Ebuyer
Case Fan | be quiet! - Pure Wings 2 51.4 CFM 120mm Fan | £7.34 @ Aria PC
Case Fan | be quiet! - Pure Wings 2 51.4 CFM 120mm Fan | £7.34 @ Aria PC
Monitor | Asus - VP228H 21.5" 1920x1080 60Hz Monitor | £115.00 @ Amazon UK
Keyboard | Corsair - STRAFE Wired Gaming Keyboard | £70.74 @ Aria PC
Mouse | Logitech - G402 Wired Optical Mouse | £29.99 @ Amazon UK
Headphones | Logitech - G230 Headset | £37.00 @ Amazon UK
Other | SteelSeries QcK Gaming Mouse Pad (Black) | £8.99 @ Amazon UK
| Prices include shipping, taxes, rebates, and discounts |
| Total | £1236.01
| Generated by PCPartPicker 2017-08-21 04:37 BST+0100 |
You can get a copy of Windows 10 here and this link will teach you how to create a bootable USB drive.
This video will walk you through the build process step-by-step, and this one will walk you through the setup of your new rig from overclocking the RAM to installing Windows. If you need to update your BIOS to successfully overclock the RAM (you probably will), this video will walk you through that process.
To actually complete the build, you're going to need a few tools.
The essentials are a screwdriver, a pair of scissors/wirecutter, and zip ties for cable management. Some useful tools (that aren't mandatory) include a small screwdriver for the hard to reach places in the case, a magnetic screw tray to keep track of all those pesky screws, and an anti-static mat (can't find a link to one, but the brand I'd recommend is called ModMat).
I know it seems overwhelming, but you'll be okay! You have plenty of resources (and this sub!) available to help, and you're welcome to PM me for any help you may need :)
Feel free to ask anything!
I use this rack: https://www.amazon.com/gp/product/B00SA23E80/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
result: http://imgur.com/6DGdD8W
Rearranging things to fill in the new drawers. Finally can get the pliers in one place, or most of them. There are some in boxes and pouches, because that's where they should live, and a few that won't fit.
Big kudos to /u/PM_YR_MOOSE_KNUCKLE for recommending the pliers rack. Putting them on their side makes storage so much more efficient.
edit: some day, I'll remember how to link stuff
I just donated a decent amount of money to my local church for you. That was much appreciated since they were trying to raise money in order to buy a magnetic tray for the daily mass prayer. Apparently they are extremely expensive.
I even gave them a link for a decent one: http://www.amazon.com/Titan-TIT11061-Mini-Magnetic-Tray/dp/B000HYL20G
They promise they will all pray for you although they are doubtful about a full recovery.
Take care!
I can't help you with your question unfortunately but may I recommend something similar to these trays. I've been using a similar one for a couple years and they are a life saver for electronics work.
/u/BurpSnarts has a great DIY suggestion. I have a couple of suggestions for the wrenches and sockets if you just want to order something. For the wrenches, check out the Ernst gripper wrench organizers:
http://www.amazon.com/Ernst-Manufacturing-5048-Red-10-Wrench-Organizer/dp/B007DP0BI6
You can organize the metric and US wrenches pretty easily. Since you don't have a box to keep them in just yet, those organizers will keep the wrenches secured if they're in a bag or whatever. I have a couple of those organizers for different wrench sets and couldn't be happier. For the sockets, they have a twist lock socket rail that will keep things secure:
http://www.amazon.com/Ernst-Manufacturing-8450-Universal-Multi-Drive/dp/B00CHJHA8W/
I haven't used one myself but they have good reviews.
Been there. First big tool kit of whatever type. The parts work for non-daily usage, but the storage system is awful. I suggest this (or a variant), we use it in a pro shop.
https://www.amazon.com/03966L-Universal-Organizer-80-Piece-Multi-Drive/dp/B005ANSPW2/ref=mp_s_a_1_8?keywords=socket+wrench+storage&qid=1566263375&s=gateway&sprefix=socket+wrench+st&sr=8-8
https://www.amazon.com/Hansen-Global-Metric-Socket-Storage/dp/B001C6NL52/ref=sr_1_4?ie=UTF8&qid=1517575540&sr=8-4&keywords=socket+organizer
Oh, nice. I have an olsatools socket tray sitting in my amazon wishlist for a while, and I was about to pull the trigger at $40. The kobalt looks identical, just that it's in blue.
https://www.amazon.com/dp/B0776Z4ZTQ
Definitely going to pick up one or two of the kobalt trays now. Thanks for the tip.
I used something like this. Just make sure its magnetic.
https://www.amazon.com/Lisle-40200-Magnetic-Socket-Holder/dp/B0002STSTY
I used one of these throughout my entire build and it was fantastic to have. If you have a Microcenter near you they sell them by the checkout for $1.99. I grabbed it at the last second, luckily.
https://smile.amazon.com/Torin-581T-Magna-Caddy-Organizer/dp/B00SWRDU5A
or
https://smile.amazon.com/dp/B00Z2R1OJM
Look into getting one of those plier organizers. I got one from amazon. Changed my life. Super cheap too. not an associate link
Also what brand are those hose pliers? I think I need some.
https://www.amazon.com/dp/B07F4RJLQ3/ref=cm_sw_r_cp_apa_TJY7BbAQJH39N
Just like this but a little more home made.
Plier Organizer Rack for Tool Box Storage and Organization Holder Stores a Variety of Spring Loaded, Regular, Wide Handle Insulated Pliers | Fits Nicely in Toolbox Drawer or Chest Drawers (2) https://www.amazon.com/dp/B07F4RJLQ3/ref=cm_sw_r_cp_api_i_WCW7CbESCD5BM
Plier Organizer Rack for Tool Box Storage and Organization (2 Pack) Holder Stores a Variety of Spring Loaded, Regular, Wide Handle Insulated Pliers | Fits Nicely in Toolbox Drawer or Chest Drawers https://www.amazon.com/dp/B07F4RJLQ3/ref=cm_sw_r_cp_apa_yqZTBbW4T7P73 I had to trim one slot off for it to fit
I have these dividers and I love them. They're perfect for a large toolbox. The rest of the page shows you can buy it piecemeal if you have special needs.
Small boxes within drawers are a godsend. You can buy pre-built tool-specific ones like on the site I linked to above, but you can also find useful similar items at dollar stores.
If you use sockets, nothing beats a Hanson socket tray. (Overkill tray linked, but you can buy individuals for $10 or so. Totally worth it.)
Kudos on getting the toolbox built. More fun awaits you! :-)
Edit: Oh, I almost forgot. If you have lots of pliers, this is worth its weight in gold.
It depends on your budget.
Amazon sells this $5 Wrench Organizers that fit in most tool boxes. Which are great for 99% of people.
If you want to shadow your tool box you got a few options.
Some people like Kaizen Foam Inserts but they are pricey as hell.
Some people also do a much much cheaper version of shadowing using Anti Fatigue Mats so its only about $2-$3 a drawer.
Here is a quick video of what it looks like when done.
You do need to switch blades on your utility knife very often though. Those mats just tear through blades.
I thought it was spelled Murlock...but whatever anyways!
/u/Hansoda seeing as the thread that spawned initially wasn't super helpful, funny tho :P, what you want to look for is entry level helpdesk support or chat support or anything like that. ISPs are typically ALWAYS looking....but if you can avoid that hell please do, you'll keep your sanity a bit longer then us here :)
But yeah in short the things I would tell you to get an understanding of are simple really:
Um...that is about all I can think of :P sorry for the super long post mate but I hope this helps and gives you a better idea of what to learn/watch/know. This all comes from my own experience and knowledge as a person who started his IT career back when I was 18 for a Call Center/then my own business/then doing work for realtors/then consultant style work/and now I'm at what is basically a bomb and munitions disposal company haha; also I'm now 27 so quite a long time doing various IT work! :D
I have more if you want.
Better yet, you can get magnetic trays to give everything a place to go and stay and be able to see everything you have in there at a glance. They come in a bunch of different shapes and sizes so you can get what you need. Here is an example.
http://www.amazon.com/Titan-11189-Magnetic-Parts-Tray/dp/B00TO7NM6Y/ref=sr_1_4?ie=UTF8&qid=1449242657&sr=8-4&keywords=magnetic+tray
I'm not sure what an add-on is! BUT this is something that would be very helpful to me! I am always dropping bolts and nuts when I work on my truck (or anything really) these things are great at helping to prevent that!
pay attention in class! (especially if you are paying for school!)
https://www.amazon.com/Hansen-Global-Metric-Socket-Storage/dp/B001C6NL52/ref=sr_1_5 maybe?
Yeah I ended up ordering these and am much happier with the space. And for the cost I think they’re actually pretty nice, fully loaded I don’t think I’d hang them like they show but in the drawer I haven’t had any problems yet. I had to get 4 though (one for 6 and one for 12 point)
https://www.amazon.com/dp/B005ANSPW2/ref=cm_sw_r_cp_api_i_-nDSCbM38JV8H
Oh good, I've never known pcpartpicker to get compatibility wrong. Plus, from what I can see your build looks great. I did want to note that a GTX 1080 will only be different from a cheaper graphics card if you have a monitor that can utilise its power, i.e. one that is 1440p and 144hz (or more). If you're using a monitor with a lower resolution or refresh rate, say a 1080p/60hz monitor that's the most common, I'd consider a cheaper graphics card (like a GTX 1060 6GB), because there will be noticeable difference in performance. Just wanted to make sure you knew that. : ) I see a lot of people overspend just to have a GTX 1080 even though there will be no difference at all in what they can see on their screen.
Getting to the question you actually asked: So people like to say that you can build the entire computer with just a #2 Phillips screwdriver (that's the "regular" size). This is basically true. I'd recommend spending $10-15 on an extra long scewdriver (10 to 12 inches). The length really helps when working deep in the case. I bought one after my second build, and since then the builds have been SO much better. I have one like this one and it's great. Especially since it's magnetic.
Another extremely useful item is a magnetic scew/bolt tray, like this one will save you a LOT of time and trouble.
The one and only screw on most builds that doesn't take a standard screwdriver is the tiny screw that holds m.2 SSDs into place. I didn't see if you have an m.2 SSD or a 2.5" one. Either way, a small precision screwdriver set can be very useful. I own this one which is extremely high quality, but there are much cheaper versions out there. They come in quite useful around the house too.
So long story short, you can basically get away with just a cheap standard screwdriver, but a couple of extra tools can make your life a lot easier.
Not an easy task to try and do. I think the only thing that will work well is to shadow the bit holder it's self. Bits will still stay organized within a holder, but have a place in the box. It all depends on the number of bits you are dealing with. Here are some products that might help.
https://www.amazon.com/gp/aw/d/B00MS3230M/ref=pd_aw_sbs_263_3?ie=UTF8&psc=1&refRID=9BACRY1QM8F393723WJ8
https://www.amazon.com/gp/aw/d/B00SWRDU5A/ref=pd_aw_sim_469_2?ie=UTF8&psc=1&refRID=E5VD9HEEQHH3RCW9CDRH
https://www.amazon.com/gp/aw/d/B01HZ5H136/ref=pd_aw_sim_469_1?ie=UTF8&psc=1&refRID=E5VD9HEEQHH3RCW9CDRH
Just screw them in. If you have left over then you came out on top. You will have extra scews for other projects!
Next time get some trays . I do pc repair and these guys really help out at keeping everything nice and organize. Really nice when you take something apart and have to leave it out for a week or so.
https://amzn.com/B001C6NL52
I have them as well. They're the only ones I've ever owned that I actually like, and don't end up throwing away in anger.
I just picked up the iFixit Pro Toolkit as well as a cheap set of screw drivers. I also use a magnet tray for holding screws (especially useful for laptops) and I lay my screw drivers in there while I'm working to magnetize the tips.
One of my cheapest (free) things I've added to my workbench recently is an old 17" Dell Ultrasharp that was given to me. It's absolutely wonderful for a tech bench. It has VGA and DVI input. It's height adjustable, and swivels. It has 4 USB ports built into it. I leave my keyboard and mouse plugged into it, as well as signal and power cables. When a machine hits my bench, I plug in one signal cable, one power cable, and one USB cable and I'm ready to go.
I paint fat rings around the handle near both ends. Red for SAE, green for metric. As that's a place where they don't typically see a lot of hand contact, the paint has survived pretty well. It's much easier to see at a glance than paint down in the lettering, which is also likely to get full of gunk and cover the paint.
My socket holders are color coded the same way.
Yup anytime. Fixing your own stuff is really rewarding. Its nice to look at how much money you saved doing a repair yourself to justify investing the money on tools and your own experience. You may break parts along the way, break tools, bash knuckles, and get frustrated but it's all part of learning and appreciating machinery. I am a firm believer that you will do a far better job and have far more vested interest in your machine than any mechanic you are paying. Check out this book if you need a good read, nice discussion on the value of working on your own things.
The option to admit defeat and take it to a shop is always there. Just remember that none of these things are magic, bikes are pretty simple machines when compared to what else is out there. Don't be afraid to set it down and come back to it later.
OH! One of these is also super useful.
If you have some free time, and don't mind the occasional swear word, this guy AvE makes some awesome videos...takes aparts things and explains what's going on, tests tools, cool fixes, general machine shop tom foolery. Worth a watch.
You'll definitely want a set of these babies:
https://www.amazon.com/Hansen-Global-Metric-Socket-Storage/dp/B001C6NL52/ref=sr_1_1?ie=UTF8&qid=1468292113&sr=8-1&keywords=socket+organizer
Yep. They're called Hansen trays I believe.
http://www.amazon.com/Hansen-Global-Socket-Tray-Pack/dp/B001C6NL52/ref=sr_1_1?s=hi&ie=UTF8&qid=1398258178&sr=1-1&keywords=hansen+socket+tray
Nah. Get a magnetic tray for automotive work:
http://www.amazon.com/TEKTON-1902-Round-Magnetic-Parts/dp/B000NPUJS0/ref=sr_1_1?s=automotive&ie=UTF8&qid=1396907827&sr=1-1&keywords=magnetic+tray
The magnet is powerful enough to hold screws in place no matter how hard it gets jostled, the tall sides prevent the screws from getting accidentally bumped, it sticks to the side of the computer case or any magnetic surface, it holds your small screwdrivers. Drop a screw on the floor ? Just rub this across the floor and the screw will get sucked up by the large powerful magnet. If you have a lot of screws, there are rectangular ones. Dry erase work on them too.
If you want to remember where the screws go, use a digital camera when taking it apart.
A wide taper reamer?
I've also seen things called a "stepless drill bit" that might do.
That's per set of 3. So you would need 2 of those sets to cover standard and metric. Looks like they're $45 right now on Amazon, thought I remembered them being a few dollars cheaper. So ok they're $5 more expensive than regular price at HF. Depending on your sales tax that makes it pretty much a wash. If the coupon works and your willing to make a couple trips then HF is a cheaper, as long as the quality is ok.
iFixit's screwdriver kit is good, but there's dozens of kits that are all fine for $30 or less. The ifixit one has pentalobe (apple) and tri-tip stuff for more uncommon screw heads.
For screws: Egg Carton, Ice Cube Tray, etc all work just fine.But this tray is neat too.
[WXTOOLS 80-Pcs Iron Premium Quality Adjustable Socket Holders, Portable Socket Organizer Tray, 1/4-Inch, 3/8-Inch, 1/2-Inch, Best Heavy Duty Socket Rail for Men https://www.amazon.com/dp/B07R2JJNNS/ref=cm_sw_r_cp_apa_i_bRNGDbXCX13R5]
Hope fully this link works, what socket set is this for?
a friend of mine uses a small parts organizer like this
Fits commander decks (even double sleeved!), and he just puts a piece of foam on top of each deck that's large enough to make sure the lid holds the decks in. Cheap, easy to carry, and well worth the 20 bucks.
I hate when this happens. Bought one of these and they changed my life lol
LPT: Use some of these. It is a life saver.
http://www.amazon.com/Titan-TIT11061-Mini-Magnetic-Tray/dp/B000HYL20G
invest in these...
https://www.amazon.com/Rosewill-Anti-Static-Components-RTK-002-Yellow/dp/B004N8ZQKY
https://www.amazon.com/Titan-Tools-11061-Magnetic-Parts/dp/B000HYL20G/ref=sr_1_1?ie=UTF8&qid=1504297831&sr=8-1&keywords=magnetic+bowl
https://www.amazon.com/TANKING-Reusable-Fastening-Microfiber-Cloth-6/dp/B01K021UAG/ref=sr_1_7?s=electronics&ie=UTF8&qid=1504297886&sr=1-7&keywords=velcro+cable+ties
Have you ever tried organizers like these? I really like them. Saves room in your drawer and I keep them a lot neater when I use organizers. I'm a lot more likely to put them back in order.
These are the ones I have. I also have some of the Olsa single rails. High quality aluminum.
https://www.amazon.com/dp/B0776Z4ZTQ/ref=cm_sw_r_cp_api_i_CoDWCbZPMT2M6
These may be good for your application, are your tools always on the road with you? Mileage beats on stuff like this. http://www.amazon.com/Ernst-Manufacturing-8451-Universal-Multi-Drive/dp/B00CHJHA7I/ref=sr_1_3?ie=UTF8&qid=1427225641&sr=8-3&keywords=socket+rail
They look like these.
http://www.amazon.com/Hansen-Global-92000-Metric-Storage/dp/B001C6NL52/ref=sr_1_1?ie=UTF8&qid=1426925670&sr=8-1&keywords=hansen+socket+tray
But $10 is a lot for a plastic tray with some numbers on it.
Thanks! Link: https://www.amazon.com/gp/product/B07NW1MCJH/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1
Possibly this one; I picked mine up last week and so far it holds my pliers... What more can you ask from it. https://www.amazon.com/gp/aw/d/B00SA23E80/ref=gp_aw_ybh_a_12?ie=UTF8&psc=1&refRID=Q6ZQZKJKV7E8F0R0PA07
http://www.amazon.com/gp/aw/d/B0002STSTY/ref=mp_s_a_1_1?qid=1415561780&sr=8-1
This one. It's perfect for holding edh decks, and game dice, and extra stuff. It's the one I have. I found mine at target. Same price. The bins/cups are moveable too! So you can customise how you want your stuff to be organized.
https://www.amazon.com/gp/aw/d/B00Z1K625Q/ref=psd_mlt_nbc_B004G5Y7YK_pr
Edit: to say "for holding edh decks, and game dice, and extra stuff"
SECTION | CONTENT
:--|:--
Title | How to build a computer in 30 minutes with EasyPCbuilder! - Gaming PC
Description | Learn the best way to build a computer from start to finish with a Computer Engineer, in only 30 minutes!! A no-nonsense, straightforward video on the computer building process. Ever wanted to build your own computer? This video will show you how. Want to ensure you build the fastest, best quality and best value for money computer on the market today? Buy one of the EasyPCBuilder Build Guides from our website! (link below) The EasyPCBuilder Build Guides explain the PC Building process in a no...
Length | 0:30:55
SECTION | CONTENT
:--|:--
Title | Shopping for a New PC as Fast As Possible
Description | People often ask "should I buy a pre-built computer or build my own?" This is (I hope) the ultimate guide to your options when shopping for a new computer! Sponsor message: Try Hotspot Shield for FREE and get 20% off an Elite subscription with offer code LINUS. Go to http://bit.ly/HSShare Sponsor Link: http://linustechtips.com/main/topic/57757-hotspot-shield-sponsor-link/?hl=%2Bhotspot+%2Bshield LinusTechTips forum link: http://linustechtips.com
Length | 0:06:05
SECTION | CONTENT
:--|:--
Title | What is a Core i3, Core i5, or Core i7 as Fast As Possible
Description | What the heck is the difference between a Core i3, Core i5, and Core i7?? What do these terms mean? Vote for my next punishment: http://bit.ly/linuschoice Check out Fractal Design's excellent products: http://www.fractal-design.com/ Intel's Naming Scheme Guide: http://www.intel.com/content/www/us/en/processors/processor-numbers.html
Length | 0:04:32
SECTION | CONTENT
:--|:--
Title | SSDs vs Hard Drives as Fast As Possible
Description | SSD vs HDD or hard drive is a question that I get a lot, so I took a few minutes to answer it for you. Enjoy :) Sponsor message: Give Audible's monthly audiobook service has more than just audiobooks! - use audible.com/techquickie to get the first one for free! Sponsor Link: http://audible.com/techquickie
Length | 0:04:06
SECTION | CONTENT
:--|:--
Title | What SSD To Buy As Fast As Possible
Description | What should you look for when buying an SSD beyond capacity and sequential performance numbers? Dollar Shave Club link: http://dollarshaveclub.com/linus Follow: http://twitter.com/linustech Join the community: http://linustechtips.com
Length | 0:06:38
SECTION | CONTENT
:--|:--
Title | What is Overclocking as Fast As Possible
Description | Overclocking is the black magic. Or is it? Sponsor message: Give Audible's monthly audiobook service a try. If you're as tired of Top40 hits as I am, it's a perfect alternative! - use audible.com/techquickie to get the first one for free! Here's my latest overclocking guide: https://www.youtube.com/watch?v=0CHs5_TdpXE Suggest a Future Fast As Possible: http://linustechtips.com/main/news-reviews-article-guides/linus-videos-news-and-ramblings/47101-temporary-thread-for-tech-quickie-video-sugg...
Length | 0:02:33
SECTION | CONTENT
:--|:--
Title | How To Install Windows 8.1 From USB Guide/Tutorial (Easiest Method)
Description | This is a real quick guide on our preferred method of installing Windows 8.1 from a USB flash drive. There are lots of other ways, but this is the one that is consistently most reliable and super easy to boot! What you need: 4GB+ Flash Drive Links: Get Windows 8.1 ISO from CD Key: http://windows.microsoft.com/en-CA/windows-8/create-reset-refresh-media Get 90 day Eval copy of Windows 8.1: http://www.microsoft.com/en-us/evalcenter/evaluate-windows-8-1-enterprise Windows ISO to USB tool: http://...
Length | 0:04:33
SECTION | CONTENT
:--|:--
Title | How to Install Windows 10 from a USB Flash Drive
Description | How to install Windows 10 from a flash drive. you would need a 4GB USB flash drive, or 8GB for the 64-bit version. Microsoft Windows 10 https://goo.gl/QbeS9R Disable UEFI http://www.avoiderrors.net/?p=18375 Change the boot order http://www.avoiderrors.net/?p=10562 Upgrade to Windows 10 If you don't want to loose data: https://youtu.be/e07j60JK58A How to Format and Clean Install Windows 10 https://youtu.be/E49IjCMKU4g
Length | 0:07:31
SECTION | CONTENT
:--|:--
Title | Top Must-Have Items When Building a PC!
Description | Squarespace Sponsor Link: www.squarespace.com/bitwit 10% off with offer code BITWIT Here are some handy things I've collected over the years for smoother cleaner PC building. US Klein No. 2 Phillips 7'' Screwdriver: http://amzn.to/2cu6zrA Maxcraft 60609 Pocket Screwdriver: http://amzn.to/2d139f3 ModRight Mod-Mat: http://amzn.to/2cqQVRa ModRight Mod-Mat XL: http://amzn.to/2d34jcG Capri 10012 Magnetic Screw Tray: http://amzn.to/2d13Chz Delcast MT02 Magnetic Project Mat: http://amzn.to/2ccZM7z A...
Length | 0:08:04
SECTION | CONTENT
:--|:--
Title | Graphics Card Specs: The Basics
Description | TL;DR - Reviews and benchmarks are the most important thing to look at when buying a new graphics card. But if you ARE curious as to what these specs mean, here's a video! Buy Graphics cards at NCIX: Canada: http://www.ncix.com/category/video-cards-5e-108.htm US: http://www.ncixus.com/products/index.php?minorcatid=108 VIDEO: How much VRAM do you need? https://www.youtube.com/watch?v=Utv144XeHag See news sources + discuss on our Forums: http://www.ncix.com/article/NMG.htm?url=http://forums.n...
Length | 0:08:10
SECTION | CONTENT
:--|:--
Title | Easiest Way To Setup a New Computer ft. Ninite - Tech Tips Suggested Software
Description | This episode of TTSS, we take another look at Ninite. It takes all the software you want and packs it into a single installation process. The entire NCIX team all use Ninite and we just can't give them enough credit. Learn More: http://goo.gl/TRf4R9 What Chrome Plugins We Use: https://www.youtube.com/watch?v=87nvzH6PPZg&list=PLhOBXy8CSH6mimsviutuS-VrxmKgqEZE_&index=4 Join the conversation on our community: Forums: http://forums.ncix.com/ Facebook: https://www.facebook.com/NCIXdotCOM Twitter: ...
Length | 0:08:32
****
^(I am a bot, this is an auto-generated reply | )^Info ^| ^Feedback ^| ^(Reply STOP to opt out permanently)
It was not hard to build the mobo into the case, just keep on top of your cable management. If you can, remove the HD sled first (unless of course you need it). All the screws come with the products that I purchased, yes. Be careful about stripping screws, just use the proper driver (no power!). I believe I have 8 standoffs mounted + 1 nub that comes pre-attached to the case. I probably watched ALL the youtube videos, lol. https://www.youtube.com/results?search_query=fractal+meshify+c+build
Things I made sure I had for my build before all my parts showed up.
I got most of these items as a tip from a youtube video but I can not find it at the moment. Yeah, definitely let me know if you need help with anything or just want me to show you "how I did it". The manual for the mother board has the header LEDs defined on there, there is one dead spot (no pin) in the top right, obviously dont use that one but also don't use the one below it even though its labeled ground for the reset button (thats the only issue I had).
This Maybe tray is an exageration. It's a small bowl
Just use a parts tray, it is magnetic so he screws won't get lost. If you can't figure out where the screws go back, you shouldn't be taking the PC apart in the first place!