Best hobby tool magnifiers according to redditors
We found 211 Reddit comments discussing the best hobby tool magnifiers. We ranked the 77 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 211 Reddit comments discussing the best hobby tool magnifiers. We ranked the 77 resulting products by number of redditors who mentioned them. Here are the top 20.
13 dollar amazon special! https://www.amazon.com/dp/B0769LQPGZ/ref=cm_sw_r_sms_c_api_i_mnRjDb10K6X2E
It's a helping hands. For soldering typically but for any time you need a device to hold something in place to free your hands to work on it somehow.
https://www.amazon.com/Neiko-01902-Adjustable-Magnifying-Alligator/dp/B000P42O3C
They are 1/72, and I use these.They help a lot (more than even brushes).
Did you know Amazon will donate a portion of every purchase if you shop by going to smile.amazon.com instead? Over $50,000,000 has been raised for charity - all you need to do is change the URL!
Here are your smile-ified links:
these
---
^^i'm ^^a ^^friendly bot
Helping hands
https://www.amazon.com/Neiko-01902-Adjustable-Magnifying-Alligator/dp/B000P42O3C/
Can use for fly tying or holding circuit boards while soldering, etc.
you only need to go as long as it takes to make a burr. After the finest stone has made a burr on one side, then the other, strop the knife on leather, denim, or particle board using very light pressure until the burr is gone. Consider getting a jewler's loupe if you want to visually compare each step
http://www.amazon.com/iKKEGOL-Magnifier-Jewelery-Detecting-Identifying/dp/B00CJVFR24/ref=sr_1_1?ie=UTF8&qid=1453738014&sr=8-1&keywords=loupe+40x
Ooh! I got these recently and they've helped SO MUCH! The light goes right where you need it, and you can direct it slightly up or down, too. I also never realized how helpful magnification is until getting these. My stitches are so much more even!
I would honestly buy them separately. A helping hands like this one, and a lamp like this.
Try Cura. The latest version is supposed to be very good (always free). I use version 15.04.6 because if it ain't broke don't fix it I guess haha. Support removal is very tricky. You should try using surgical forceps, and have a magnifiying goggle set so you can see how well your doing up close like these: https://www.amazon.com/Headband-Magnifier-Dicfeos-Magnifying-Replaceable/dp/B075WR4M99/ref=sr_1_3?ie=UTF8&qid=1527009556&sr=8-3&keywords=magnifying+glass+goggles
Also helps a ton with painting the little details :-D
Also near-sighted and astigmatic, I used to get this until I spent the money on getting a decent headset magnifier, and it seemed to go away.
It was an old-school magnifier, like this one but even less modern without the swappable lenses.
After some quick googling:
Tools
The 11-in-1 card tool.
United Cutlery card tool
Victorinox Swisstool
Victorinox Swisstool Lite
Tool Logic SVCII
Tool Logic ICC1B
Tool Logic T1BCC
Knives
Cardsharp knife
Nemesis Titanium Card II knife
Snody Crisis Card Gen II
Titanium Charge Card
Utility
Fresnel lens
Diamond Sharpening Card
Eon Classic flashlight
Note that, aside from the 11-in-one tool, none of these products are endorsed by me. Links are provided strictly for educational purposes.
Edit: Formatting
I use this thing
http://www.amazon.com/dp/B00AQAANDS
Reaper makes Learn to Paint kits. I've used them to reinforce some of what I've learned at local painting meetups and I've liked them. I ended up grabbing a large Army Painter paint set and then had a wet palette and a Winsor & Newton brush recommended to me from a Zombicide painting group. They also pointed me to a head-mounted light/magnifying glass and some brush soap.
A great place to start is the mini painting starter sets by Reaper:
https://www.amazon.com/Reaper-Miniatures-08906-Learn-Paint/dp/B00NTMC49G
https://www.amazon.com/dp/B01N458GBK/
They're not too expensive, and they are a great intro to mini painting. They also come with pieces to practice techniques on, and a lot of paints to work with as well. I'd get those, and maybe some brushes.
I also would recommend a wet palette to keep paints wet between painting sessions, magnifying glasses to help see, and a mini holder.
I also got these brushes, which seem to be working well for me, and have a mix of useful ones.
A set of helping hands with alligator clips can hold the pieces still, so you only have to use one hand to paint.
I didn't even bother to try to paint decent faces without. Here's what I bought:
https://www.amazon.com/dp/B071VZ4X6P/
Works wonders: light where you need it, every detail clear.
A bit heavy on the nose(due to the batteries), but 1-2h are no problem. There are loads of these glasses for sale, they all look the same just differ in prices.
Parts
Build Tools
Gorruck 34L GR2 Coyote Tan - a good bag, heavy, uncomfortable, probably give it to my grandchildren in like 50 years
Flip Flops - generic things
Bigblue 28W solar charger - very good, can charge my battery up during the day if i leave it in the sun which I've never really done honestly
Jakemy hardware tools - seamed useful? i've never needed this
Army glove shells - i thought i used these a lot and were indistructable but now that i think of it, i don't use them that often and are probably pretty cheaply made.
Sharpie, pen, all weather notebook - probably should switch over to a fisher space pen...
Straws - these are probably already broken.
Whistle - really really really loud
Fire-striker, matches, lighter - i'm not sure i have enough ways to start a fire
Fresnel lens - ok, now i have enough
LED flashlight - i used to go running in the middle of the night with this flashlight, its tiny
LED flashlight - this isn't the one i have but looks kinda similar? i don't remember where i got mine
Earbuds - generic cheap earbuds
Leatherman Surge - given to me by my wife for passing the bar. thanks wife!
First Aide kit - i put mine together from stuff i've stolen from friends houses whenever i go over and use the bathroom
playing cards - these look very similar to the ones i have, they are plastic so they won't get rained on
glasses/ sunglasses - i have really bad vision
personal hygiene kit - aahhhh dry shaving
Sawyer Mini / syringe, collapsible canteen (dirty), heavy duty straw - i've never used this
collapsible canteen (clean) - i've never used this either
sewing kit - i've used this a lot
ID tags - i guess if i get blown up they'll know my blood type?
garbage bag - for when my pockets are full
elastic bands - i use these when packing to keep rolled socks and things from falling apart
Salt - i have nooooo idea why i have this
cooking grate - i'm not going to hold meat over a fire with a stick like some sort of caveman
heavy duty ziplock bag - in case my mapcase breaks and other reasons
rip-patch - leftover from when i needed a pack because i bought a crummy cheap inflatable sleeping pad.
Army Fleece Beanie - i always keep this at the top of my pack
4 Bungie Cords - not the one i use but similar. to make a field-expedient shelter
Trowel - for disposal of biological wastes
Lensatic compass - because GPS should only be a backup
Pocketboy 130 folding saw - i have a bigger one for yardwork, this small one is really great
Tent stakes - for tent staking
Ravpower 26800 Battery - use this all the time can fast chage my stuff
Battery Battery holder, cables, wall charger - all fits togehter like glove!
Army Poncho - wear it, make a tent out of it etc
Microfiber towel - not the one i use but similar. i mainly use this for when the kids accidentally fall in a lake like they tend to do for some reason
Down Jacket - cheap chinese knockoff... i feel bad for not buying american
Wet weather top - not sure this is worth the space/weight
Wet Weather bottom - not sure if this is worth the weight/space
Silkweights - PJs! and warmth
Jungle Blanket - this is a lot better than the army's woobie. lighter and warmer
Gransfors Bruks Wildlife Hatchet - again, gift from wife. she wanted me to chop things and be more manly, generally. now i come home with parts of wildlife for her to cook
Map of New England - or, how i stopped worrying and love dismounted land navigation
PT belt - keeps me safe in all situations
Compression straps - i don't like lashing things to the outside but i guess i can if i wanted to
Fork and Spoon - stole these from the kitchen. i'll probably be replacing this soon with something titanium.
​
EDIT: i just priced it out: $1,585.08 total
I can't stand any of my GW brushes. Recently got some Winsor Newton series 7. The difference is night and day. I can do small details with a size 1 ( M layer brush in GW speak ). I also picked up some cheap synthetic, Foundation series, Winsor newtons from WH Smiths for £4. Even they are better than the GW brushes.
Winsor Newton series 7
Click the link above buy one in size 1 and one in size 0, thank me later ;).
On a side note the best thing I bought recently for painting is a pair of these
Magnifying Glasses. Now I can actually see where the end of my paint brush is going!
I havent built that model but to answer your second question...Be cautious of build guides (or lack thereof). The one you linked has a really good guide. Step by step, clear pictures, and in color. So far, I've found Befaco, AI Synthesis, and Trogotronic to have really good guides.
Also, take your time. Its better to go slow and be sure of your work than rush. Tape! Tape helps me a lot by holding small pieces in place. If you can, get this circuit board holder. I got this magnifying headband for free (that style, not that specific one) and its been really helpful as well.
Here are my go to recommendations for beginners.
Trogotronic VCA
Trogotronic Power System
AI Synthesis
I recommend these:
http://www.amazon.com/UltraOptix-Powerful-ASPHERIC-Lighted-Magnifier/dp/B0054H1XYQ/ref=sr_1_5?ie=UTF8&qid=1397526300&sr=8-5&keywords=aspheric+lens+7x
They are for sale at Fry's Electronics if you have one nearby, and the lenses are great quality. I built a Durovis Dive and used these lenses. I eventually ordered a retail Durovis Dive and found that the lenses linked above were much better than the ones it came with, so I made a new bracket for them, and the improvement was amazing.
Incidentally, they are the same lenses recommended for the FOV2GO, which was made by some college folk.
More info on lens suggestions from them here:
http://projects.ict.usc.edu/mxr/diy/lens-sources-for-fov2go/
I'm using Amazon links as requested, but if you have a local big box tool stop you can get the store brand of most all these items for the same price or less. I know from personal experience, that from the tools I've listed all but two of the items are cheaper in store than on Amazon.
Everyone needs a knife! (~$7 home depot)
Razor blade
Where are you going to keep everything? (~$10 home depot)
Utility Sack
You'll need a good all around screw driver. (~$8 home depot)
6-in-1 Reversible Screwdriver
Need some basic general maintenance pliers? (~$20 home depot)
Pliers Set
Ratcheting screwdriver for those repetitive screw jobs. (~$20 sears)
Ratcheting Screwdriver
Where the hell did I put that T6?
Magnetic Precision Screwdriver Set
Where did that damn screw go?
Flashlight
Extra stuff!
I recommend the ball end ones specifically if you don't have a good angle on what your trying to get at (cough towel bar cough cough).
Long Arm Ball End Hex Key Wrench Set
For those damn pesky wires and that damn lack of a third hand.
Helping hands
When duck tape and gum wont cut it.
Beginners soldering iron kit
I have used all of these specific items extensively besides the ball end hex keys, and that specific helping hands.
I did this for my phone off of this tut:
http://www.roadtovr.com/category/diy-vr/
I was in the process of inventing a foldable version when Google Cardboard came out :/
Here are two good sources for cheap lenses if you are interested:
Singles (glass)
|
Bulk (plastic)
Looks real, probably fine. Probably just paranoia over the whole fake cards thing everybody freaks out over.
What the light test shows you from the images is what you should see - the pattern of the other side with even "shadowing" throughout the card. If you could see large, abnormal blotches, or couldn't see the reverse side of the card at all, that would be the most sure sign of a fake.
Invest in a jewelers loupe - then examine all of the black lines in the text and mana cost and set symbol - the black should be solid black through the loupe - if you see the rosette pattern over any black line, this is another tell-tale sign of fakes. The rosette pattern should also be consistent and even over the whole card.
40x magnifying glass. https://www.amazon.com/Illuminated-Magnifier-XYK-Magnifying-Identifying/dp/B01N0V87F5/ref=mp_s_a_1_3?keywords=folding%2Bmagnifying%2Bglass%2BJewelers&qid=1550760041&s=gateway&sr=8-3&th=1&psc=1.
Also a second vote for Callister. Even an older edition.
+1 for the Hakko FX888D-23BY
Some solder wick and a desolder pump is something else I would add. Also a cheap tip thinner for a noob (like me). Helping hands are cheap and can be useful. Also a cheap variety pack of tips. Nothing expensive till you are comfortable with keeping them clean and tinned.
These are all things I bought when I purchased my Hakko FX888. All have been useful.
Desolder Pumps and Wick
[Tip tinner] (https://www.amazon.com/dp/B00NS4J6BY/ref=cm_sw_r_cp_apa_i_k1kZDbJ5TS5Q6)
Helping hands w/magnifying glass
Various Tips
Hakko FX888D-23BY
All of this cost me $146 shipped. Right now, it'll all total to $139.83 shipped if in the US
Keep one of these in your wallet: fresnel lens. Light, cheap, hard to break. I knew my Army training and Stoner science would intersect one day.
3-Pack Credit Card Size Pocket Fresnel Lens - Magnifier Lenses for Fire Starting https://www.amazon.com/dp/B00NWMUK0I/ref=cm_sw_r_cp_apa_vFCMzbQSW6EVQ
Try r/minipainting
I’ve used YOCTOSUN Head Mount Magnifier... https://www.amazon.com/dp/B01H8808H6?ref=ppx_pop_mob_ap_share for awhile
I was pretty worried about the eyes. They took some patience, but it wasn't too hard. The paint consistency is important. It needs to flow, but not go all over the place.
After glazing with gloss varnish a barely visible sienna oil wash was put in the bottom part of the eye to bring out the line. Then the mini was sprayed with dullcote.
I used this guy's eyes for inspiration.
I wore 1.5x magnifying glasses so I can see what I'm doing.
> wool socks
Is this in addition to the 2 pairs of socks mentioned in your "transportation" section?
> Sleep/Shelter (light tarp, 2 x 50 feet of 550 Titan survivor cord, emergency Mylar blanket, portable hammock? wool blanket? woobie? bivvy bag?)
You said "4-season." Have you tested any of this in the extremes of the seasons? Especially winter?
> Illumination (LED flashlight, headlamp, spare batteries)
Enough spare batteries? Rechargeable batteries? Way to recharge said rechargeable batteries?
> Combustion (waterproof matches in waterproof container, 5 Bic lighters, Fresnel lens, Magnesium block? Ferro rod? Survivorsteel? travel lantern? 12-hour candles?)
More ways to start a fire is always good. I see no tinder, though. Having some on hand in case you can't gather any (none around, or it's all wet) is handy, and it won't take up much space. Something like Wetfire or even cotton soaked in petroleum jelly (you can store this in a ziploc or cut straws to an inch and a half or 2 inches stuff it down in there, pinch the ends with pliers and melt them with a lighter). Maybe even just carry a tiny jar of Vaseline and some cotton swabs to make a cotton tinder stick on the spot.
> Hydration (filled 40oz stainless steel water bottle, Sawyer Mini water filter)
Consider a few collapsible water bottles. No need to keep them full. If you either know you're going to go a long stretch between water sources or you're going to wander into an area where you're not sure about the water (quality or availability), you can fill them up.
> Protection (two high-capacity 9mm handguns… make and model? How much ammunition for 2 weeks?)
"How much ammo?" depends on how much you actually need to use them. Hopefully, you'd use them zero, which means that you need zero ammo. Worst case that you live through is lucking your way through daily extended gun fights. The truth would likely be somewhere in the middle.
Let's consider weight for a moment
Most handguns sold as new in the US come with 2 magazines. Standard magazine capacity for a Glock 17 or M&P9 is 17 rounds. Glock 19 and M&P9c carry 15 rounds in their standard capacity magazines. So, 2 full mags with the gun is 34 rounds for the full sized guns or 30 rounds in the compact guns. That's about a pound of ammunition in 2 magazines (rounding because I'm lazy). If you've got 2 guns that each came with 2 magazines, you have 2 pounds of ammunition between the two guns, plus the weight of the guns and the magazines themselves.
The Glock 17 has a 4.5" barrel and weighs 24.87 ounces (1.55 pounds) with an empty magazine.
The M&P9 has a 4.25" barrel and weighs 24.7 ounces (1.54 pounds) with an empty magazine.
So, for each gun with 2 full magazines, you're talking about roughly 3.5 pounds of weight, so 7 pounds if you're carrying 2 guns. The compact versions of the guns (G19 and M&P9c) aren't much lighter, so not worth factoring the difference.
Most handgun ammo comes in 50 round boxes (some of the higher end defensive ammo comes in 20 or 25 round boxes). That 50 round box weighs between 1.4 and 1.6 pounds (depending on the weight of the actual projectile used).
1 box of ammo will give you 2 loaded magazines and 16 rounds left loose (for the full sized guns, 20 rounds for the compact guns). Might as well pop for a third magazine to stuff at least most of the ammo in. And you're adding another half pound to your load for each gun you do this for.
So, 8 pounds for 2 guns, 6 loaded magazines, and 100 rounds of ammunition. How much more weight do you want to carry?
Also, please define "high-capacity."
Make and model is debatable. Lots of folks will say "Glock" without a second thought. They're reliable, no doubt, but they don't naturally point straight for a lot of people. If you're going to practice plenty, that's not a problem. If you're not, it might be. I prefer the M&P over the Glock. It naturally points straight for me.
Honestly, this is a big can of worms with no single "correct" answer, and it actually brings more questions than answers. Things like:
And many more questions, really. It deserves its own post.
> Medical Supplementation
You asked about antibiotics. Do you know how to determine what antibiotic to use? How much of it to use? Are you allergic to any antibiotics? Allergy to the penicillin family is fairly common, for example.
Seriously consider consulting your physician about this. Tell him/her you're planning an extended camping trip and you're worried about possible infection if you get a serious cut while out. Ask about a prescription for a prophylactic course of antibiotics for such an event. They might do it, they might not. If they do, fill the scrip and make note of what it is and the dosage amount and instructions and use that as a launching point for future research.
> toilet paper coins
That looks like a bad implementation of a good idea. Carry some actual TP (same type you're used to at home, pull the cardboard tube out of the middle to help it squish flatter) and/or some wet wipes. If you don't mind the bulk and the weight, go to the baby section of Wal-Mart and grab some Parent's Choice brand baby wipes. They're not flushable, definitely not septic safe, and I have no idea how biodegradable they are, but they're surprisingly tough, and reasonably cheap. I don't recall what a pack of 80 costs off the top of my head, but a case of 1200 costs $20. If you don't want to brave the baby section, grab some Charmin wipes (which are flushable if that matters to you) from the regular TP area of Wal-Mart. Avoid the Cottonelle wipes. Their structural integrity leaves much to be desired.
Also, a way to wipe your ass isn't a "creature comfort." Personal hygiene is a necessity that becomes doubly important when SHTF.
> -folding solar panel?
If you have the space (volume and weight) and have batteries to charge (like for your lights), sure, go for it.
This is starting to get long (does Reddit have a character limit?), so I'll try to breeze through a few other things:
If we get the "WW3/national SHTF/anarchy scenario," that .22 will be good to hunt with, but crap to fight with. In that scenario, a proper AR-15 in 5.56x45 NATO would be preferable, but I wouldn't want to hump 250 miles with it in the open if I didn't have to. Consider a Pistol Caliber Carbine (PCC) that takes the same magazines as your handguns (Kel-Tec has a few options, Ruger's PC9 is promising, too). It's not as good as a proper rifle, but it will extend the useful range of the handgun ammunition and magazines you're already toting. It will also add 4-6 pounds to your load, but a decent AR will ad 6 to 8 before you factor the extra magazines and ammo.
NVG are bulky and expensive. Unless you plan to move and/or fight a lot at night, I'd skip them.
The use case you make for a gas mask can be handled by a bandana or shemagh, either of which is lighter, more compact, and have other uses. If you're expecting actual gas, grab the gas mask, otherwise it's unnecessary weight.
A lightweight vest is going to stop handgun rounds but probably not rifle rounds. It's also probably going to be hot. This one's up to you. Helmet is also a personal choice. I expect it would get more actual use saving you from tree branches and falls than gun shots, but not sure if you want the extra weight, bulk, and potential heat build-up.
Credit card sized Freznel lens
Extract from wallet, look closely at stuff or light fires/burn ants. Choices abound.
For stripping the inner usb cables, I recommend this tool.
Also highly recommend a helping hand tool; you can use that to hold the usb terminals or GX16-4 which makes soldering way easier.
I have some magnifiers similar to these that I can't paint without. Curse my old eyes.
Paintbrushes, always nice to have extras, even if low quality
Airbrush supplies if you have an airbrush, Thinner, Cleaner etc
Kneadite or milliput superfine
Extra glue, whichever you use to assemble
Exacto blades
Blue-tac
Tacky glue, aka pva glue
Certain tools you don't have, or would like. Good example would be this, good to have for precise operations.
I was looking more at something like this to not take up table space. But they both seem good!
honestly I just ordered them, they were cheap and I didn't want to mess with building my own.
http://www.amazon.com/SE-Clip--Double-Loupe-Set/dp/B000YMZJX2/ref=sr_1_14?ie=UTF8&qid=1318217887&sr=8-14
Only thing I had to do was make a little room on the hole clamp so it would sit right as I adjusted it.
My favorite magnifiers as someone who does bench work, beading, wire wrap, stonework:
http://www.amazon.com/SE-1013FL-Helping-Magnifier-Light/dp/B000Z7GGJC/ref=sr_1_6?ie=UTF8&qid=1405451223&sr=8-6&keywords=helping+hands
http://www.amazon.com/Microscope-Jeweler-Currency-Magnifier-Adjustable/dp/B00AQAANDS/ref=sr_1_9?ie=UTF8&qid=1405451254&sr=8-9&keywords=jewelers+loupe
(this thing is so much fun, and I keep one on me when running around goodwills)
http://www.amazon.com/Housweety-Professional-Jewelers-Lighted-Magnifier/dp/B005VIG6TA/ref=sr_1_1?ie=UTF8&qid=1405451281&sr=8-1&keywords=jewelers+magnifier
None of these are expensive and all are very useful.
This is the one I use:
https://www.amazon.com/dp/B073RFZS94/ref=sspa_dk_detail_6?psc=1&pd_rd_i=B073RFZS94&pd_rd_wg=Et8uj&pd_rd_r=8T1KYZ3DTY48KAPJTZBS&pd_rd_w=XJNh6
I like that it's a band (rather than having spectacle-like arms) so it won't fall off when you lean forward and that the tension of the band is easy to adjust using a knob on the back of the band.
I have one of these I find it impossible to use on a living plant. This is the one I use. It can be used with a camera or the naked eye.
I use this, the base could use a little more weight, but all in all it is great.
Brightech LightView Pro Flex 2 in 1: Magnifying Glass LED Lamp - Lighted Magnifier with Stand & Clamp - for Desk, Sewing, Table - Bright Light for Rea https://www.amazon.com/dp/B01K10XA1O/ref=cm_sw_r_cp_apap_hJbqsNahY9meL
Op posted link as new comment instead of replying, here's what they said;
"https://www.tindie.com/products/Abacomtech/ezpick-manual-pick-and-place-machine/
https://www.amazon.com/dp/B01H8808H6/ref=cm_sw_r_cp_apa_i_FNJvCb5F2HY8J (there are many other relabeled and variations of this particular one)."
In my experience those two finger turning adjustable types are garbage. They never last for very long and are dificult to manage.
I purchased these two years ago and it's all I've eve used.
[1] (https://www.amazon.com/KINGMAS-Pocket-Microscope-Jeweler-Magnifier/dp/B00AQAANDS/ref=pd_sim_200_2?_encoding=UTF8&psc=1&refRID=KEDEDRG711YM9A2DM25Y) 60x LED and adjustable. Is great for looking at trichomes.
2 40x fixed. Is great for everything else when you don't need to get as up close and personal.
Got it on Amazon https://www.amazon.com/dp/B018MRI1F8/ref=cm_sw_r_cp_api_i_0mIYCb2A9PYTP
Got the lighted magnifier there too. It can be free standing or clamp on. The ones locally available look like junk. https://www.amazon.com/dp/B01K10XA1O/ref=cm_sw_r_cp_api_i_TpIYCbFB0MCVR
https://www.tindie.com/products/Abacomtech/ezpick-manual-pick-and-place-machine/
https://www.amazon.com/dp/B01H8808H6/ref=cm_sw_r_cp_apa_i_FNJvCb5F2HY8J (there are many other relabeled and variations of this particular one).
I got this and it’s perfect. https://www.amazon.com/dp/B01K10XA1O/ref=cm_sw_r_cp_api_pazQBbKS6AWWN
helping hands are a must!
I’ve been very happy with these.
Edit: just be careful when swapping to the headband as the plastic clip broke when I did it. Nothing a little duct tape couldn’t fix though! Doesn’t matter if you’re wearing glasses with the headband.
I use this.
Works well, but feels a little cheap.
I use the Lightview Flex.
It's not the cheapest in the world but it is very bright and you have the magnifier if you need it. The flexibility of the gooseneck is great and the desk clamp is quite strong. The weighted base has good heft and doesn't move on the desk.
The downside is that the gooseneck isn't extremely long, so that could be an issue for you. I have no problems due to how I brace my elbows on my desk.
A small vise or helping hand can be invaluable, if using a helping hand I recommend wrapping the alligator clip hands in a couple layers of electrical tape as they can be quite sharp and scratch up connectors and such. Since there's virtually no risk in damaging components, most soldering irons between 60-120W should work well. Any 60/40 rosin core solder will work, if you're unable to get leaded solder due to local regulations, I've heard the 99% tin stuff is decent, again just make sure it has rosin core. A smaller tip might be beneficial if using smaller connectors such as 2.5mm. A solder sucker and wick is useful if any mistakes are made. Lastly, a DMM is helpful to make sure there are no shorts and that all connections have continuity and low resistance.
I’m also over 40 here and my eyesight just tanked as well. I recommend this instead of a mounted magnifying lens.
YOCTOSUN Head Mount Magnifier... https://www.amazon.com/dp/B01H8808H6?ref=ppx_pop_mob_ap_share
Comes with several lenses of increasing magnifying strength and doesn’t get in the way of handling things. They look goofy but I’m well behind caring at this point.
I have this headlamp and I love it.
https://smile.amazon.com/gp/product/B01H8808H6/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
I bought the surgical tubing to pull in the pots. I have not soldered in years but I researched before I started and based on good tips I bought a hotter soldering iron (40 watts +) and 'helping hands'. Both were huge and I could not have done it without the helping hands. The magnifying glass was just in the way. The alligator clips were strong so to keep them from cutting through the wires when holding them I put rubber tubing over the clips.
The soldering went so much better than I expected.
It would. Are you using a "helping hand" to hold up the board vertically?
https://www.amazon.com/gp/aw/d/B01N0V87F5/ref=oh_aui_i_sh_pre_o0_img?ie=UTF8&psc=1
I'll chime in for a recommendation for this lamp I purchased recently.
Also/additionally, try picking up a cheap pair of low-strength readers. At least in the US, they're available at most drugstores. Even a 1.00 or a 1.25 can make a big difference in discerning tiny dates on coins.
No problem :-)
I also got one of these to help hold the cables still while soldering. You could do it with pliers and elastic bands though. http://www.amazon.co.uk/gp/aw/d/B001BMSBD4/ref=mp_s_a_1_5?qid=1420010781&sr=8-5&pi=AC_SX110_SY165
Happy soldering!
Well, if you're thinking about doing it get some mylar paper from goulet and go slow and use super cheap nibs. You will break your first 4-16 nibs.
I personally like to do it on my dremel at low speeds using a finer grit spinny thing :) The way you do it is keep a vision of what the nib should look like at a very detailed level and just go slow and light with the grinding and check it with a loupe often. I use a 60x loupe (this one, it's amazing) and check the shape of the nib OFTEN. After every few seconds of work I'll check it till it's in the shape I want, then I'll take some fine files and smooth it out a bit with different sticks between 3200 and 12000 grit. I'll usually move up from 3200 and just keep going until I'm on the 12000 grit stick. I usually have the nib I'm working on in the pen by the stick tuning part but I do take out the nib when I'm using the dremel.
Now that I've gotten pretty proficient at it, it usually only takes about 5 minutes to do a nib unless it's below a F, in which case it'll take up to 10 since you really have to go slow with those because you want to keep as much material on the nib as possible, but just shape it into a finer point where the paper touches it.
This is the one I bought. There might be better ones out there, or better priced alternatives, but I bought this one and am happy with it.
https://www.amazon.com/gp/aw/d/B00CJVFR24/ref=ya_aw_od_pi?ie=UTF8&psc=1
This?
My SO's birthday is coming up, and he likes to casually paint Warhammer-models. He has requested something to help hold the pieces while he paints, but hasn't specified a preference for a particular type of tool.
I was looking at something like this: http://www.amazon.co.uk/dp/B001BMSBD4 and I'm wondering if I'm waaaay off target or not. If anyone has any recommendations or helpful tips I would be super grateful!
I'd also like to get him some additional stuff if the price of this ends up being very low, so if anyone can recommend some additional basic useful tools or accessories that they feel helped them out while painting you'll help me make my SO very happy! :)
Thanks!
I actuall did away with fresnel and put in some +3.0 plastic lenses.I have just ordered this lens and will see how it looks.https://www.amazon.ca/Professional-Jewelers-Lighted-Magnifier-Visor/dp/B005VIG6TA/ref=cm_cr_arp_d_product_top?ie=UTF8
Mod pics http://imgur.com/a/aU3kT Night and day compared to the fresnel lense.It looks better in person as i can actually read the text on the coffee cup quite clearly.
Apologies, just realized I did not reply to your RCA cable comment.
When I did the tonearm rewire, I also swapped out the RCA cables which were connected to the board. I did both at once so I can't tell how much of this was the cable replacement vs the tonearm rewire - but I noticed a good drop in the overall noise floor and better clarity. In my head, I credit the noise floor drop to the RCA replacement and the clarity to the tonearm review - but again, don't take my assumptions as gospel. It did seem like a worthwhile change.
Take a look at KAB, that's where I picked up the tonearm rewire stuff and it was cheap and defiantly worth the effort. I have very limited soldering experience and it still only took me about 1.5 hours to get everything pulled apart and reassembled with the RCA cable soldering and tonearm rewire soldering. Just need to be delicate. If I were to do it again, I'd def pickup an inexpensive set of helping hands, something like this to make the job easier as it is delicate work.
Currently with the SME 309, I'm using the Sumiko Premier PIB-1 Interface Box so I get to pick the cables running out from there to my phono stage. Currently using bluejeans RCA interconnects and have no complaints. Super 'high-end' cables an area I haven't been convinced enough that it makes that huge of a difference, so I'm going to stick with what I have as I have no issues.
The run in a little longer than I like and it crosses paths with some of the power cables behind my components - so a good cleanup and cable management project is needed. I picked up the supplies a few weeks back to take care of cable management but don't want to commit to it until after the external power supply change as I know that'll need to be considered when I end up taking care of all the wire management work.
All the best brother (or sister)!
Get a pair of watch repair specs with different lense strengths. Can pick up a pair for a few bucks from amazon.
https://www.amazon.com/dp/B0716ZCYXZ/ref=cm_sw_r_cp_awdb_t1_72AtDbM4K8G62
Those eyes are really cool. I've got a bunch of mini's showing up soon from the Bones 3 kickstarter and will have to try that out on some of the bigger pieces before working it down to the smaller ones. Unfortunately most of the large models I have now are Big stompy robots (privateer press Cryx) and they don't really have eyes on them.
I have not tried a magnifier head set. I tried using the magnifier on a pair of helping hands but I had no sense depth perception so it didn't really work out for me. I've heard that the headsets work fairly well and you can maintain your sense of depth. Let's just say they're on the old wishlist so I can try them out.
Glad to hear it!
For soldering, I'd recommend doing what I did and just go to Home Depot or Lowes or a hardware store and get a few feet of wire, maybe a few different gauges of it, take it home and practice. Cut it, strip it, solder it together, and use electrical tape or heat-shrink wrap to cover all exposed metal. Rinse wash repeat. Did that 3 or 4 times and got more comfortable with it.
Grab one of these helping hands along with a basic soldering kit off amazon and you're good to go.
https://www.amazon.com/Neiko-01902-Adjustable-Magnifying-Alligator/dp/B000P42O3C/ref=sr_1_4?keywords=helping+hands&qid=1569619359&sr=8-4
Have fun!
I’m a tricomb guy, grab a cheep scope off of amazon, https://www.amazon.ca/KINGMAS-Microscope-Jewelry-Magnifier-Jeweler/dp/B00AQAANDS/ref=mp_s_a_1_5?keywords=mini+microscope&qid=1567317008&s=gateway&sprefix=mini+micr&sr=8-5 Or search mini microscope and pick one
This one is 12$ Canadian and works perfect for this, the tricombs will start clear and then start to get cloudy and then start to turn Amber. I usually check the middle of the main cola on the plant and chop when it’s approx 60/40 Amber to cloudy. it’s a personal preference thing as the high changes depending on ratio. You should be able to find some you tube videos fairly easily that’ll help. The scope is also a must for identifying some pests as well.
Great looking plant, good luck!
I seem to have linked the wrong scope, you should get at least a x45 sorry about that
3-Pack Credit Card Size Pocket Fresnel Lens - Magnifier Lenses for Fire Starting https://www.amazon.com/dp/B00NWMUK0I/ref=cm_sw_r_cp_apa_mm4.ybTZ614H8
Brown Big Skinny bifold with 50-100 in cash, driver's license, credit card, voter card, insurance card, fishing license, AAA card, emergency contacts, a family photo, a small amount of duct tape, and a fresnel lens. All packed up it's still pretty thin.
This is slightly different from what you have above, but if you're using a cell phone and you want to get macro shots, give one of these a try. You can just hold it up to the back of your cell phone camera lens, and then directly over the coin. It's great for getting macro shots of specific parts of a coin.
I just bought both of these because I have been buying revised Duals off of eBay.
http://www.amazon.com/iKKEGOL-Magnifier-Jewelery-Detecting-Identifying/dp/B00CJVFR24?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00
http://www.amazon.com/GridLite-UV-Blacklight-Flashlight-Detector/dp/B017LM7QHE?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00
The Loupe comes with a built in Light and Blacklight, no battery needed when opening.
You probably don't need to buy the individual blacklight, but if you do I believe it requires 3 AAA batteries.
Buy a set of Helping Hands. Yes, you can solder without one, but it makes it so much easier that for a couple bucks it's absolutely worth it.
If you need to solder on a pcb you'll want a temperature controlled soldering station, other essentials are rosin core solder, some flux to apply before soldering, and a helping hand to hold the pcb/component and wire in place when soldering. I leave my soldering station at a little less than 350 when I'm tinning wires and soldering on a pcb. Wipe excess solder off the iron, heat up the spot you want to solder to with the wire in place, then apply solder to the wire when the flux has smoked off, it should flow into the joint. You don't want to keep heat on a pcb for too long as it can damage components on the board. Make sure you tin the tip/s of the soldering iron with solder before and often during use, or the tips will oxidize and refuse to tin until you scrape the oxides off with a razor knife. Typically a problem at high temps, around 300C solder will melt and oxides form very slowly and the tip will stay hot without needing a retin for a 5-10 minutes. I usually set my temp on max when I first turn it on and hold a bit of solder to the tip and then turn it down when the solder melts. Saves a few minutes of warm up between use.
If you need to heat up a larger surface area (like a battery terminal) for tinning or soldering it helps to bump up the heat - sanding a large surface also will help. Steel and other metals may require use of a corrosive flux made specially for that.
That's about all I know XD
This is another popular option: https://www.amazon.com/KINGMAS-Pocket-Microscope-Jeweler-Magnifier/dp/B00AQAANDS/ref=pd_sim_201_4?_encoding=UTF8&pd_rd_i=B00AQAANDS&pd_rd_r=T85T5H6TCG8FQT8Q80XR&pd_rd_w=mh4B9&pd_rd_wg=9WA7H&psc=1&refRID=T85T5H6TCG8FQT8Q80XR
Multiple vendors sell that same one for multiple price points.
I'd opt for a freestanding magnifying glass or combo helping hand over one of those
I have these. They're pretty nice but way too heavy for the small little nose piece. I have to take breaks from them. I think I'm just going to a regular old magnifying glass and light on a stand for my desk.
I bought this LED lamp with a magnifying glass back in January and, up until last week, it’s been my only source of light besides whatever is overhead in the room.
Brightech LightView Pro Flex... https://www.amazon.com/dp/B01K10XA1O?ref=yo_pop_ma_swf
This lamp is great. However, I found that because it was so bright, it was basically the only source of light my res could see on the model and it cast pretty harsh shadows, making it difficult to really paint well and straining my eyes.
So I purchased this lamp last week as a “fill” light:
RMJ Dimmable LED Desk Lamp... https://www.amazon.com/dp/B0714KST8G?ref=yo_pop_ma_swf
And it’s been such a wonderful addition. The “study” setting is perfect daylight hue and it fills my workspace with enough light so that I’m not straining my eyes and have relatively even lighting over my models while I paint.
Hope that helps.
A good magnifying glass is just as important as a good iron, especially once you realize you're not 25 anymore.
Any chance it's still salvageable or did you burn a hole through one of the chip? ;)
It was another amazon find for me: https://www.amazon.com/dp/B01K10XA1O/ref=cm_sw_r_cp_apap_Fh9FMsyEilKRq Its not too bad. I dont really use the magnifying glass though
I bought one from amazon that was prettys wide and it still didnt work.
Give this a try! It works for me:)
https://www.amazon.com/dp/B01H8808H6/ref=cm_sw_r_other_apa_Guuvzb7QXP4D4
After the thread here: https://www.reddit.com/r/MTGLegacy/comments/6k77zx/buying_duals_is_terrifying/ I figured I'd try to disprove the rumor that the text is the biggest give-away (hint: it's not), and bring some degree of confidence to those who do want to buy duals (hint: just buy a $5 loupe!)
 
Here's the loupe I use: https://www.amazon.com/KINGMAS-Pocket-Microscope-Jeweler-Magnifier/dp/B00AQAANDS/ref=sr_1_11?ie=UTF8&qid=1498759657&sr=8-11&keywords=jewelers+loupe
Hehe I’m still relatively new too. And I too make polymer clay things, the tiny stuff really does hurt your eyes. I bought one of these things as it helps for the tiny stuffs: head mount magnifier
I would get some sort of modeling magnifying glass. I plan on getting these from Amazon,
https://www.amazon.com/dp/B0769LQPGZ/?coliid=I5OWQJK0P9F95&colid=WAZGGT5LLK4T&psc=0&ref_=lv_ov_lig_dp_it
What you're referring to is called a Third Hand or Helping Hand. I've got one, but have not yet used it!
One of these and a cheap laser pointer.
Total outlay <£5, and more accurate and it won't fall off or leave marks on the screen or have that annoying cable dangling down.
A pocket microscope. Might get it tomorrow when I get paid and take pictures on my phone using it. :o
I bought a cheap loupe to inspect the tip... https://www.amazon.ca/KINGMAS-Microscope-Jewelry-Magnifier-Jeweler/dp/B00AQAANDS
So far, I'm on the original 0.4mm nozzle, and I only change them to switch sizes... 0.8 for big "structural" work, and 0.2 for 1:100 scale minis.
I've run roughly 10kg through the 0.4 nozzle, including several spools of "silk" and thermo-chromatic.
The most important things are a tank and the ability to fill the tank to a PSI above a minimum of 80 or so. A tank makes it so the compressor doesn't have to run constantly, and creates a buffer so the air pulses of the compressor aren't transmitted to the brush where they can cause dotted rather than smooth lines. You want the compressor to be able to put out a higher PSI because you want the tank to hold enough so you can spray for longer at pressures of 60 PSI or below for longer intervals before the compressor has to refill the tank.
For model painting, most of your spraying will be best done at 20-30 PSI. Higher PSIs like 60 tend to be either for cleaning, or stuff like textile paints (i.e. T-shirt artists). The little "fishtank" compressors like the Ninja Jet can only deliver a max PSI of around 15 or so, which is on the very bottom edge of what most brushes can work with. PSIs of 15 and below are mainly used for tiny close-in detail work with highly thinned paint, and going that low works better with brushes that are designed specifically for detail, rather than "jack of all trades" workhorses.
Different brushes require different CFM (cubic feet per minute- a measurement of air volume rather than pressure), and little "fishtank" compressors are bare minimum here as well, so there will be many brushes where they'll make the brush spray poorly because they physically can't provide enough air to keep up at any pressure. A good target CFM rating for a tankless compressor is 1.5.
A tanked compressor can technically get away with less CFM, since it's not supplying the brush directly, but unless you want to have to stop painting whenever the compressor has to top up the tank, you want the compressor to have enough CFM to supply the brush WHILE also filling the tank, which means check your brush manual/documentation for its CFM, and look for a compressor that is specced over that by at least 1/2. The higher the CFM, the faster the tank will fill. Unfortunately I could not find specs for the Patriot that list CFM, but 1.5 is probably still a good start for a tanked compressor.
"Master" and other such Chinese import brand compressors are popular because people think they're cheap, but for very little extra a brand like California Air Tools will get you better QC, support, reliability, and specs. Chinese airbrushes are comparatively cheap, but the compressors aren't really, so there's not much reason to get the Chinese ones IMO.
Avoid regular hardware-style compressors unless you're painting in a very noise-tolerant environment, as even the "quiet" ones are LOUD AF. Seriously: when the descriptions/reviews say "super quiet" they mean by construction site standards, not household appliance standards.
As to fittings: if you live in a particularly dry climate (like Arizona, say), you can get away with not using a moisture trap, but even there it's good practice to have one just in case. If your climate is any more variable or humid than that, you will want a moisture trap. You can just get one from the local hardware store though: it doesn't have to be a special type. Always place the trap last in the air supply/fitting chain before the airbrush hose, so: compressor-> tank-> regulator-> moisture trap-> airbrush hose-> airbrush. Or if using a bench block as described below: compressor-> tank-> regulator-> connecting hose-> bench block regulator-> moisture trap-> airbrush hose-> airbrush.
In the US, compressors usually have 1/4 NPT fittings. In Metric countries, 1/4 BSP. These fittings are cross-compatible enough that you can use them together with teflon tape.
For hobby and fine art airbrushing, I HIGHLY recommend a lightweight hose like this over braided hoses. Braided hoses are for industrial-type settings like auto painting shops, where hoses need to be extra hard wearing.
BTW, when painting, loop the hose once around your forearm so if you accidentally drop the brush, the hose acts as a lanyard preventing the brush from hitting the floor. I feel like I'm constantly hearing horror stories about people damaging their brush by dropping it when preventing this is so easy.
A tanked compressor with come with a regulator. These are perfectly usable, but imprecise. It's not strictly necessary, but I do highly recommend using the built-in regulator as a step-down regulator, and getting a 0-30 or 0-60 PSI regulator to chain after it. I use one of these on my setup, and it makes adjusting airflow much better.
If you plan on locating your compressor directly on or under your "workbench" surface, that's all you need. If the compressor is going to be outside immediate/easy reach, it can be good to mount your regulator and moisture trap on a separate "bench block" so you can put it on/under your bench within easy reach. This is what I had to do with my setup (I mounted the regulator and moisture trap on a scavenged heavy steel bookend). In that case, you'll want/need a hose like this to go between the compressor and the regulator/filter block.
There are "extras" you can get like a quick-connectors and MAC valves, but I don't personally recommend them. If you're only using the compressor for your airbrush, you don't need quick connectors on the compressor side of the hose, and IMO quick connectors on the brush side don't actually save you time/energy as it only takes 2 seconds to unscrew a brush from the hose. If your regulator is in easy reach, a MAC valve similarly does not save you any time/effort. Both of these also add lots of bulk to the brush stem, which is undesirable if your instinct is to hold/use the brush like a pen instead of a gun. There are mini-filters that go between the hose and the brush, but I generally don't recommend them for the same reason: too much added bulk on the brush stem: it's better to to add to your main filters if you need better filter performance.
I don't have a Badger Patriot, but my understanding is that it's a good brush. I have two Badger SOTAR models, and if they're any indicator, I'd expect spray performance to be comparable to IWATA, but fit & finish to be more raw and "industrial" outside of the nozzle and needle, so a little fussier to keep clean. It should be much better and more reliable than a 20$ "Master" or "Point Zero" or whatnot.
The threads in the head assembly can be a little "gritty" on Badger brushes OOB. If that's the case, I recommend lapping them with something like Flitz to ensure a good seal. Basically just put a tiny dab of compound on the male threads, then screw them in and out about 20 times to polish off the burrs that are causing the gritty/sticky feeling. Make sure to clean the residue off thoroughly before spraying again.
For maintenance, get a roll of lint-free shop paper towels, a couple packs of interdental brushes from the local dollar store, a box of q-tips, and a box of round wood toothpicks. Use paper towels and q-tips wetted with solvent/thinner to clean the cup and needle, the interdental brushes to clean the passageways/tubes in the body, and use a wood toothpick whittled to a needle taper and soaked in thinner to clean the inside of the nozzle (don't use metal tools to clean the nozzle, as they might scratch it or flare the tip). Occasionally you'll need to inspect the needle tip or nozzle for gunk or damage, so you'll want a high-X pocket magnifier similar to this. Also a stick of wax-based lip balm to help the threads in the head assembly maintain a good air seal (apply a tiny amount to the male threads before reassembly after cleaning).
Get or make a spray-out pot. They're easy to DIY out of a margarine tub or soda/juice bottle, so although nice, it's not strictly necessary to buy one.
Get or make an airbrush stand/holder. This is not for storing the brush, but rather for having a way to set the brush down while in-in use without spilling the paint cup. Again: these are easy to DIY, so you don't have to splash cash on one unless you really feel like it.
Hope that helps!
These are the ones used in the DK1 and the FOV2GO : http://www.amazon.com/UltraOptix-Powerful-ASPHERIC-Lighted-Magnifier/dp/B0054H1XYQ
I believe this is the one:
https://www.amazon.com/Yoctosun-Magnifier-Professional-Jewelers-Interchangeable/dp/B01H8808H6/ref=pd_lpo_vtph_328_bs_t_1?_encoding=UTF8&amp;psc=1&amp;refRID=TCHXY0SG58VH85TADDJT
Meat rub and spices gift set
BBQ Tools gift set
[Race car wine bottle holder](https://www.amazon.com/Premium-Metal-Race-Bottle-
Holder/dp/B01GIG86H8/ref=sr_1_2?ie=UTF8&qid=1482234804&sr=8-2&keywords=nascar+gift)
Coin magnifier
First let me say that disposable contacts are one of the best investments I ever made, for this reason among others.
Otherwise, things like Wizard (traditional or modern) or Mad Scientist work very well with glasses, especially if you have something like this to clip on.
You can find sunglasses to go over your frames at places like Walgreen's or CVS. I've worn out a few pairs, myself. Then you can do any costume that calls for sunglasses: Terminator, Zombie Kim Jong Il, or whatever. :)
I use these. I frickin' live in them when doing electronics. They fit over my glasses, and work really well straight out of the box.
No. It's just a magnifying glass that has a 15X loupe built in.
https://www.amazon.com/gp/aw/d/B0188JAPGI?psc=1&amp;ref=ppx_pop_mob_b_asin_title
A handheld for checking trichomes, I like these little cheapies: https://smile.amazon.com/gp/product/B00AQAANDS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1
But checking for broad and russet mites, the USB plug-in is the way to go.
Amazon.
I have:
Generic Hobby Knife - Generic hobby knife kit. Blades were shit so I buy Xacto brand but the knives and case are good.
Needle Files - Extremely useful for polishing off mold lines or smoothing cuts.
Adjustable Jeweler's Saw - Handles a ton of different size blades for cutting metal, plastic, or wood.
Swivel Handle Pin Vice - Probably the best tool you can buy. Great for customizing what your troops are carrying.
Third Hand - Stupidly useful. Mostly for gluing.
Jeweler's Saw Blades - Bought these for my saw. Useful. Others might be better.
Micro Drill Bits - Bought for my pin vice. Useful. Others might be better.
Mini Drill Bits - Bought for my pin vice. Useful. Others might be better.
Really comes in handy for me.
http://www.amazon.com/gp/aw/d/B009NOG9TA?cache=784b6a5bb71e1cfedcc95cad9b82aafe&amp;pi=AC_SX110_SY165_QL70&amp;qid=1407091929&amp;sr=8-22#ref=mp_s_a_1_22
I got these at my local Fry's and they work great: http://www.amazon.com/gp/aw/d/B0054H1XYQ?pc_redir=1404448648&amp;robot_redir=1
https://smile.amazon.com/gp/product/B01H8808H6/ref=oh_aui_search_detailpage?ie=UTF8&amp;psc=1
they're ok, but they don't offer much magnification and the led is finicky. there's a makerspace by me with a microscope and it makes me really want my own for small smds, but i think you can get down to 0805s at least without needing that, and i dont need to go smaller than that yet
I use https://www.amazon.com/gp/product/B01H8808H6/ref=oh_aui_detailpage_o07_s00?ie=UTF8&amp;psc=1
After I did a decent bit of research a few months back I ended up getting this one and enjoy it quite a bit.
i want to start painting the pilot figures. i'm thinking of buying a magnifying glass desk lamp. do you guys use such things? is it worth it? if so, any recommendations?
from my cursory research, seem this one may be decent value for relatively cheap price point.
https://www.amazon.com/gp/product/B01K10XA1O?pf_rd_p=183f5289-9dc0-416f-942e-e8f213ef368b&amp;pf_rd_r=4WEDB459278EGVMBZEX9
Good advice here. Also, if you're going to continue painting, consider investing in one of these. It makes a huge difference when painting in small areas and tightening up lines.
https://www.amazon.ca/gp/product/B0188JAPGI/ref=oh_aui_detailpage_o06_s00?ie=UTF8&amp;psc=1
I got one of those. Its nice, got a regular magnifier and then the loup style on the side is 15x i think. And plenty of light. The 3 batteries that came with it i couldnt find replacements for, but it took 2 357s just fine.
I was using an empty small pill bottle, using some old poster tack to affix the miniature to the cap. Then I got a little "helping hands" on Amazon, though gripping old miniature bases with the alligator clips can be a little wonky sometimes, but it at least allows me to manipulate the miniature and then let go and have it just sitting on its own.
Yeah, I wasted so much paint on my partchment paper pallet prior to buying the wet pallet. I dunno what I was doing... I was planning on making one out of tupperware, but couldnt find a sponge at Michaels, so just bought it instead.
I actually purchased a jewelers headset that I love, https://www.amazon.com/gp/product/B01H8808H6/ref=oh_aui_search_detailpage?ie=UTF8&amp;psc=1
It has a light and interchangeable lenses from 1x to 3.5x
This helps me so much when soldering. I'm not sure how much it would help your specific weld you have to do but it will help in the future
http://www.amazon.com/TEKTON-Helping-Hand-with-Magnifier/dp/B000P42O3C/ref=sr_1_1?ie=UTF8&amp;qid=1421774456&amp;sr=8-1&amp;keywords=helping+hand+soldering